Technical Data; Noise Information - Milwaukee Heavy Duty M18 BMS12 Notice Originale

TECHNICAL DATA

Cordless metal shears
Production code
Battery voltage
No-load speed
Minimum cutting radius
Max. cutting capacity
Steel 400 N/mm²
600 N/mm²
800 N/mm²
Aluminium 250 N/mm²
Weight according EPTA-Procedure 01/2014 (2,0 Ah)
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger

Noise information

GB
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 62841
Vibration emission value a
Uncertainty K=
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR METAL SHEARS
Use machinery, accessories, tools, etc. As set out in these instructions.
Give due consideration to your working conditions and the type of
work. Using machines for other than their intended use may result in
dangerous situations.
Always wear goggles when using the machine. It is recommended to
wear gloves, sturdy non slipping shoes and apron.
Clamp your workpiece with a clamping device. Unclamped workpie-
ces can cause severe injury and damage.
English
12
h
M18 BMS12
4776 43 02...
... 000001-999999
18 V
0 - 2500 min
180 mm
5,5 m/min
1,2 mm
0,95 mm
0,8 mm
2,0 mm
2,3 kg
-18°C ... +50°C
M18B...
M12-18...
78,2 dB (A)
89,2 dB (A)
4,75 m/s
1,5 m/s
When cutting, hold the tool so that the blades are in firm contact
with the material for the fastest cutting. Apply even pressure. Too
much pressure will tend to jam the tool or cause a rough cut.
Please note that the machine will automatically accelerate back to its
original operating speed if the load is removed from it. Never lay the
power tool down until the accessory has come to a complete stop. The
tool may jam, leading to you losing control of the machine.
Remove the battery pack before starting any work on the appliance.
WARNING! To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack
or charger in fluid or allow a fluid to flow inside them. Corrosive or
conductive fluids, such as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., Can cause a short circuit.
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
M18 BMS20
4776 44 02...
... 000001-999999
18 V
-1 0 - 2500 min -1
180 mm
5,5 m/min
2,0 mm
1,6 mm
1,2 mm
3,2 mm
2,34 kg
-18°C ... +50°C
M18B...
M12-18...
78,2 dB (A)
89,2 dB (A)
2 7,07 m/s 2
2 1,5 m/s 2