Accessories - Milwaukee 6520-21 Manuel De L'utilisateur

Selecting the Speed Range
The speed control dial controls the maximum
strokes per minute. The speed will remain
variable to the chosen dial setting by use
of the trigger switch. Refer to the chart for
recommended dial settings.
SUGGESTED
MATERIAL DIAL SETTINGS*
Mild Steel 2-3
Wood 5
Nail-Embedded Wood 5
Stainless Steel 1-3
Drywall 4-5
Fiberglass 1-3
Plastics 1-3
Cast Iron 2-3
Non-Ferrous 2-3
Metals
* These are only suggested settings; the
actual optimal setting may vary depend-
ing on line voltage, blade selected and
user preference.
Trigger Speed Control Switch
These Sawzalls ® are equipped with a trigger
speed control switch. It may be operated at
any speed from zero strokes per minute to
full speed. Always start tool before blade
contacts the workpiece. To vary the speed,
simply increase or decrease the pressure on
the trigger. The further the trigger is pulled,
the greater the speed. To stop the tool, re-
lease the trigger and allow the tool to stop
completely before removing from a partial
cut or before laying the tool down.
General Cutting
For straight or contour cutting from an edge,
line the blade up with your cutting line. Before
the blade contacts the workpiece, grasp the
handle fi rmly and pull the trigger. Then guide
the tool along your cutting line. Always hold
the shoe fl at against the workpiece to avoid
excessive vibration.
Cutting Metals
Begin cutting at a slow speed, gradually in-
creasing speed as you cut. When cutting into
metals or hard materials that can not be cut
from an edge, drill a starting hole larger than
the widest part of the blade. Extend blade life
by using a solid blade cutting lubricant.
WARNING
To reduce the risk of explosion,
electric shock and property dam-
age, always check the work area
for hidden gas pipes, electri-
cal wires or water pipes when
making blind or plunge cuts.
Plunge Cutting
®
Your MILWAUKEE Sawzall is ideal for
plunge cutting directly into surfaces that
can not be cut from an edge, such as walls
or fl oors. Orbital action is recommended for
plunge cutting. Plunge cutting may be done
two ways depending on how the blade is
inserted. Column A shows how to plunge
cut with the teeth of the blade facing down.
Column B shows how to plunge cut with the
teeth of the blade facing up.
NOTE: Orbital action will not operate if the
blade is installed upside down.
Do not plunge cut into metal surfaces (see
"Cutting Metals").
1. Insert the blade into the tool.
If you inserted the blade with the teeth
facing downward, hold the tool as shown
in Column A, resting the edge of the
shoe on the workpiece.
If you inserted the blade with the teeth
facing upward, hold the tool as shown in
Column B, resting the edge of the shoe
on the workpiece as shown.
2. With the blade just above the workpiece,
pull the trigger. Using the edge of the
shoe as a pivot, lower the blade into the
workpiece as shown.
10
3. As the blade starts cutting, raise the
handle of the tool slowly until the shoe
rests firmly on the workpiece. Then
guide the tool along your cutting line to
acquire the desired cut.
NOTE: To make plunge cutting easier, use
a heavy gauge blade and install the blade
with the teeth facing upward as shown in
Column B.
Cat. No. 6523-21
Fig. 7
A B
Fig. 8
Cat. No. 6520-21, 6536-21,
and 6538-21

ACCESSORIES

WARNING
To reduce the risk of injury, always
unplug the tool before attaching or
removing accessories. Use only spe-
cifi cally recommended accessories.
Others may be hazardous.
For a complete listing of accessories refer to
your MILWAUKEE Electric Tool catalog or go
on-line to www.milwaukeetool.com. To obtain
a catalog, contact your local distributor or a
service center.
®
Quik-Lok Cord Sets
®
10' Quik-Lok Cord Cat. No. 48-76-5010
25' Quik-Lok ® Cord Cat. No. 48-76-5025
Carrying Case
Cat. No. 48-55-2055
Orbital Pipe Clamp System
Cat. No. 49-22-1016
Keyed Blade Clamp Kit
Cat. No. 49-22-5016
See Pages 38 & 39 for a listing of Sawzall
Blades.
11
®