Status Indications At The Pa-4000Rc; Settings At The Pa-4000Rc; Specifications; Mixer Pa-6040Mpx - Monacor PA-6040MPX Mode D'emploi

When an announcement via a different
zone paging microphone is being made, the
LEDs BUSY of the respective PA zones will
flash. It is not possible to make announce-
ments via multiple zone paging microphones
at the same time (even if different zones are
to be addressed).
When the current announcement is being
made via a zone paging microphone of the
same or higher priority, you must wait for the
announcement to finish. Only a microphone
of higher priority can interrupt the announce-
ment ( chapter 6.5.2 for priority setting).
3) Keep the button TALK (43) on the microphone
pressed and speak into the microphone car-
tridge (40). The LED indicator above the but-
ton will light up; the input signals of lower pri-
ority at the mixer will automatically be muted
( table fig. 5 in chapter 3).
4) If required, use the control AUDIO LEVEL
(44) to readjust the volume of the announce-
ment. The volume controls for the outputs (9)
will have no effect here.

6.5.1 Status indications at the PA-4000RC

In addition to the indicators BUSY and TALK
described above, the zone page microphone
provides the following status indicators:
POWER / CPU ERROR (34) – will light up when
the supply voltage is available, and will start
flashing in case of a malfunction of the micro-
processor in the PA-4000RC
MIC FAULT/ LOW VOLTAGE (35) – will light up
in case of a microphone failure, and will start
flashing when the supply voltage is too low;
an additional power supply unit may be used
when the supply voltage is too low (
ter 5.5.2, step 3)
SIGNAL (36) – will light up when a microphone
signal is available
EMER. (41) – (one for each PA zone)
are without any function when the PA-4000RC
is used with the PA-6040MPX

6.5.2 Settings at the PA-4000RC

The three switches of the DIP switch block (39)
on the rear side of the desktop microphone pro-
vide the following functions:
CHIME – in the position ON, a chime will first
sound when the button TALK (43) is pressed;
the tone of the chime will be the same as the
chime tone that is triggered by a pushbutton
connected to the mixer; the tone can be
selected in the mixer ( chapter 5.8.1)
PRIORITY – in the position ON, the PA-4000RC
will take priority over the other units where
this function has not been activated and will
interrupt their announcements
COMPRESSION – in the position ON, the
dynamics of the microphone signal will be
attenuated in order to reduce distortions when
announcements are made in a loud voice

7 Specifications

7.1 Mixer PA-6040MPX

Frequency range: . . . . . . . . . . . 20 – 20 000 Hz
S / N ratio
via LINE input: . . . . . . . . . . . > 87 dB (A filter)
via MIC input: . . . . . . . . . . . . > 65 dB (A filter)
THD:
via LINE input: . . . . . . . . . . . < 0.05 % (1 kHz)
via MIC input: . . . . . . . . . . . . < 0.1 % (1 kHz)
Inputs CH1 – CH4
XLR / 6.3 mm jack
(input sensitivity, impedance, connection type)
"MIC": . . . . . . . . . . . . . . . . . . 2.5 mV, 5 kΩ, balanced
"LINE": . . . . . . . . . . . . . . . . . 245 mV, 15 kΩ, balanced
Inputs CH5 – CH6
RCA: . . . . . . . . . . . . . . . . . . . . . 245 mV, 15 kΩ,
Input PAGING
plug-in screw terminals: . . . . . . 245 mV, 10 kΩ, balanced
Inputs LOCAL INPUT
6.3 mm jack: . . . . . . . . . . . . . . . 245 mV, 5 kΩ, balanced
Outputs OUT
XLR: . . . . . . . . . . . . . . . . . . . . . 1.23 V, 600 Ω, balanced
Output REC OUT
RCA: . . . . . . . . . . . . . . . . . . . . . 775 mV, 3 kΩ,
Output MONITOR
6.3 mm jack: . . . . . . . . . . . . . . . 775 mV, 100 Ω,
Tone controls
chap-
BASS: . . . . . . . . . . . . . . . . . . ±10 dB, 100 Hz
TREBLE: . . . . . . . . . . . . . . . ±10 dB, 10 kHz
Power supply
Mains operation: . . . . . . . . . . 230 V~ / 50 Hz
Power consumption: . . . . . 15 VA max.
Emergency power supply: . . 24 V
Current consumption: . . . . 500 mA max.
Ambient temperature: . . . . . . . . 0 – 40 °C
Dimensions (W × H × D): . . . . . 482 × 90 × 305 mm,
Weight: . . . . . . . . . . . . . . . . . . . 4.4 kg
Pin configuration of the input jacks CH1 – CH4 (22)
XLR
1 = ground
2 = signal + (+15 V phantom power)
3 = signal
6.3 mm jack
Pin configuration of the input jacks LOCAL INPUT (17)
6.3 mm jack
All rights reserved by MONACOR
manual may be reproduced in any form or by any means for any commercial use.
Pin configuration of the output jacks OUT (16)
(−1 dB)
Pin configuration of the output jack MONITOR (20)
7.2 Zone paging microphone PA-4000RC
Power supply: . . . . . . . . . . . . . . 24 V
unbalanced
Power consumption: . . . . . . . . . 63 mA
Audio output
S / N ratio: . . . . . . . . . . . . . . . . . > 60 dB
THD: . . . . . . . . . . . . . . . . . . . . . < 0.5 %
Frequency range: . . . . . . . . . . . 150 – 15 000 Hz
unbalanced
Dimensions (W × H × D): . . . . . 110 × 48 × 155 mm
Weight: . . . . . . . . . . . . . . . . . . . 700 g
Connection:
unbalanced
Max. number of units: . . . . . . . . 32
Total connection length: . . . . . . 1000 m max.
Note: An additional power supply unit will be required
when the total connection length exceeds 500 m or
when more than 10 PA-4000RC are connected.
2 RS
- (+15 V phantom power)
T = signal +
-
R = Signal
S = ground
T = signal +
-
R = signal
S = ground
Subject to technical modification.
® INTERNATIONAL GmbH & Co. KG. No part of this instruction
XLR
1 = ground
2 = signal +
-
3 = signal
6.3 mm jack
T = signal
S = ground
(16 – 35 V ) via
PA-6040MPX or
power supply unit
Rated level: . . . . . . . . . . . . . 245 mV
Impedance: . . . . . . . . . . . . . 600 Ω
Connection type: . . . . . . . . . balanced
RJ45
13