Connecting And Aligning The Antenna; Power Supply; Making The Adjustments; Settings In The On-Screen Menu - Monacor Security AV-5810RDX Mode D'emploi

4.2.5 Connecting and aligning the antenna

Connect the supplied antenna (3) to the jack "antenna
socket" (16). For a larger range it is also possible to
connect to this jack another 5.8 GHz antenna of the
series DX-58/.. of the programme range from
MONACOR. The reception antenna must be aligned
in parallel to the transmitting antenna (also see chap-
ter 4.3.2 Channel selection). By turning the reception
antenna (3), align it vertically or horizontally:
audio A video 1 antenna 2
socket
max. DC 7 - 30V
DIN-AV audio B remote
42V
switching channel
control
0,5A
AV channel
Vertical polarization

4.2.6 Power supply

For power supply a regulated power supply unit is
required with an output voltage between 7 and 30 V
and an output current of 400 mA as a minimum, e. g.
PS-1000ST from MONACOR.
In case of power supply units with variable output
voltage, adjust the voltage between 7 V and 30 V.
Connect the power supply unit via a low voltage plug
5.5/2.1 mm (outside/inside diameter) to the jack
"DC 7 - 30 V" (15). Observe the correct polarity in any
case: apply the positive pole to the inner contact of
the plug.

4.3 Making the adjustments

The AV-5810RDX has 48 programmes on which the
channel numbers and further functions can be stored
via an on-screen menu (see chapter 4.3.1). The re-
ceiver is programmed ex factory as follows:
Programme
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 – 48
audio A video 1 antenna 2
socket
max. DC 7 - 30V
DIN-AV audio B remote
42V
switching channel
control
0,5A
AV channel
Horizontal polarization
Channel Frequency (MHz)
1 5732
2 5741
3 5750
4 5759
5 5768
6 5777
7 5786
8 5795
9 5804
10 5813
11 5822
12 5831
13 5840
14 5849
15 5858
16 5867
16 5867
The other functions are preprogrammed for all pro-
grammes as follows:
on the menu page 1
Name no name entered
AFC off automatic fine tuning off
Video normal video signal not inverted
AV-Rel. n.c. when receiving a video signal, the
contacts are closed
SW-Rel. n.c. with activated control channel the
contacts are closed
on menu page 2
Audio on audio reproduction activated
Signal off no signal sound activated
Auto off with switching mode activated the
programme is skipped
Hold off with switching mode activated the
dwell time adjusted in the line
"Auto" is kept
If this factory setting is sufficient, the on-screen menu
need not be called but only the corresponding pro-
gramme has to be selected with the button "P+" or
"P-" (6) [see chapter 5].

4.3.1 Settings in the on-screen menu

Switch on the receiver with the switch "power" (1).
Select the programme to be adjusted with the button
"P+" or "P-" (6). Keep the button "OK" (7) pressed for
approx. 3 seconds until the first menu page appears
on the screen. If the receiving signal is too poor or
missing, the menu is highlighted in blue colour for bet-
ter viewing.
Program
Name
Freq.
Channel
AFC
Video
AV-Rel.
SW-Rel.
Level
First menu page
Program
Audio
Signal
Auto
Hold
Day
Month
Year
Hour
Minute
Level
Second menu page
1) To change functions, select the corresponding
menu line with the button "P+" or "P-" (6) and
adjust it with the button "L-" or "L+" (5).
1
....
5732,00 MHz
01
off
normal
n.c.
n.c.
-6-7-8
1
on
off
off
off
15
09
2006
16
44
-6-7-8
13