Intended Use - Redstone MT100 Instructions D'origine

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

of the workpiece.
12 Avoid abnormal posture
– Make sure that you have secure footing
and always maintain your balance.
– Avoid awkward hand positions in which
a sudden slip could cause one or both
hands to come into contact with the saw
blade.
13 Take care of your tools
– Keep cutting tools sharp and clean in
order to be able to work better and more
safely.
– Follow the instructions for lubrication
and for tool replacement.
– Check the connection cable of the elec-
tric tool regularly and have it replaced
by a recognised specialist when dam-
aged.
– Check extension cables regularly and
replace them when damaged.
– Keep the handle dry, clean and free of
oil and grease.
14 Pull the plug out of the outlet
– Never remove loose splinters, chips or
jammed wood pieces from the running
saw blade.
– During non-use of the electric tool or
prior to maintenance and when replac-
ing tools such as saw blades, bits,
milling heads.
– When the saw blade is blocked due to
ADDITIONAL SAFETY INFORMATION
• Do not cut material that is too small to be
safely supported.
• Avoid awkward hand positions where a
sudden slip could cause a hand to move into
the cutting off wheel.
• Always keep hands and fingers away from
cutting off wheel.
• Do not attempt to cut material that is not
securely fastened or clamped.
• Do not attempt to cut material too fast while
cutting.
• Never start the angle grinder with the cutting
off wheel pressed against the stock.
• When cutting a large workpiece make sure
the material is in safe cutting position.
• Should any part of your angle grinder be
missing, damaged or fail in any way or any
electrical component fail to perform properly,
• The dust produced at work may be
harmful to health, flammable or explosive.
Therefore, it is necessary to take appropriate
protective measures. Many types of dust are
carcinogenic, for example. Use a suitable
The machine corresponds with the valid EC
guideline.
• Before starting work, all guards and safety
devices must be fitted to the machine.
• The machine has been designed to be
operated by one person. Within the working
area, the operator is responsible with regard
to third persons.
• All safety and danger warnings attached to
the machine must be observed.
abnormal feed force during cutting, turn
the machine off and disconnect it from
power supply. Remove the work piece
and ensure that the saw blade runs free.
Turn the machine on and start new cut-
ting operation with reduced feed force.
15 Do not leave a tool key inserted
– Before switching on, make sure that
keys and adjusting tools are removed.
16 Avoid inadvertent starting
– Make sure that the switch is switched off
when plugging the plug into an outlet.
17 Use extension cables for outdoors
– Only use approved and appropriately
identified extension cables for use
outdoors.
– Only use cable reels in the unrolled
state.
18 Remain attentive
– Pay attention to what you are doing. Re-
main sensible when working. Do not use
the electric tool when you are distracted.
19 Check the electric tool for potential dam-
age
– Protective devices and other parts
must be carefully inspected to ensure
that they are fault-free and function as
intended prior to continued use of the
electric tool.
– Check whether the moving parts func-
tion faultlessly and do not jam or wheth-
shut off switch and remove plug from power
supply outlet Replace missing, damaged or
failed parts before resuming operation.
Save these instruction
Warning! Don´t use the machine without a
guard.
Before each use always the blade by visual
inspection.
Warning! Do not use abrasive cutting discs
with flaking, cracking or other damage.
Use a cutting disc, the permissible speed
of which is at least the same as the ma-
chine idling speed. Check the cutting disc
before use.
Wear helmet and apron at work.
Warning! Don´t use the machine in an ex-
dust extractor and wear a mouth guard. The
light metal dust may burn or explode.
• Never stand in front of the machine aligned
with the disc. Always stand at the side of the
cutting disc. Your body is better protected
Intended use m
• All safety and danger warnings attached to
the machine must be kept in complete and
legible condition.
• With the tools and accessories offered, the
machine has been conceived for steel and
nonferrous metals only.
• The maximum and minimum dimensions
of the used workpieces should not be
exceeded.
• Only use machines which are free from
LEROY MERLIN • Rue Chanzy - Lezennes 59712 Lille Cedex 9 - FRANCE
er parts are damaged. All parts must
be correctly mounted and all conditions
must be fulfilled to ensure fault-free
operation of the electric tool.
– The moving protective hood may not be
fixed in the open position.
– Damaged protective devices and parts
must be properly repaired or replaced
by a recognised workshop, insofar as
nothing different is specified in the oper-
ating manual.
– Damaged switches must be replaced at
a customer service workshop.
– Do not use any faulty or damaged con-
nection cables.
– Do not use any electric tool on which
the switch cannot be switched on and
off.
20 ATTENTION!
– The use of other insertion tools and
other accessories can entail a risk of
injury.
21 Have your electric tool repaired by a quali-
fied electrician
– This electric tool conforms to the ap-
plicable safety regulations. Repairs may
only be performed by an electrician
using original spare parts. Otherwise
accidents can occur.
plosive atmosphere or where sparks could
cause fire, explosion, etc.
Warning! The blade is running after swit-
ching off the machine after another.
Warning! Make sure that when working in
dusty conditions for free cooling vents.
Disconnect the machine from the power
supply first and clean the vents using a
soft brush, if the removal of dust should be
necessary.
Warning! Before use, attach the cut-off
wheel correctly and tighten down all parts.
Let the machine run in safe keeping idle for
30 s. And keep the machine immediately
and switch off the blade when considerable
vibration.
against fractions if the cutting disc breaks.
• No offcuts or other workpiece parts removed
from the cutting area, as long as the engine
is running and the saw unit is not located in
the rest position.
defects. Keep safety precautions and possi-
ble hazards in mind. Use only according to
instructions. Fully eliminate (or have elimina-
ted) any defects which can lead to reduced
safety.
• The safety, work and maintenance instruc-
tions of the manufacturer as well as the
technical data given in the calibrations and
dimensions must be adhered to.
• Relevant accident prevention regulations and
15

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

3903701924

Table des Matières