Disassembling/Assembling; Overhauling; Disposal; Warranty - Terrier FSV Mode D'emploi

Depending on the defects noted:
- dismantle and clean the clamp (see Chapter 7 -Disassembling/Assembling) or
- have the clamp overhauled by Terrier Lifting Clamps B.V. or a recognized mechanical
repair centre (see chapter 8 - Overhauling).
If in doubt consult your supplier.
7

DISASSEMBLING/ASSEMBLING

The clamp can be easily disassembled for cleaning and inspection.
Disassembling
Please make use of the following sequence (see construction drawing on page 32):
- Open the clamp to its full extent.
- Remove the retaining pin (9) and the spindle head (6).
- Remove the retaining pins (8) and the link pin (7).
- Remove the lifting shackle (3) and the spacers (5).
- Unscrew both clamping parts from the threaded spindle (4).
- Clean all parts with a standard degreasant.
- Grease the shackle pin (7), threaded spindle (4) and spindle bushes (5) with bearing
grease.
Assembling
Assemble all the parts in reverse sequence.
Note: The two spindle bushes must be screwed on to the threaded spindle over the same
length in relation to the centre, before the spindle head is fitted.
- Make sure that always new and original retaining pins are inserted and do so with the
aid of a hammer, combination pliers and pin punch.
- When replacing parts, always use original Terrier components.
- Remove any burr with a file.
If in doubt consult your supplier.
TBS
Important! Before starting disassembling the clamp, mark each part in such a way that they
are easily reassembled in the original position.
Disassembling the TBS
- Remove the retaining pin (5), with which the lifting shackle spindle (3) is secured, from
the frame (1).
- Remove the lifting shackle spindle (3) and the lifting shackle (4).
- Unscrew the screw spindle (2) from the frame (1) and remove it.
Assembling the TBS
When reassembling the clamps, assemble all parts in reverse order. To ensure the safety of
the clamp, only use the original Terrier replacement parts when repairing the clamp. Make
sure they are marked to allow proper identification.
If you carry out any inspections, repairs or modifications yourself, you will nullify all forms
of guarantee and product liability.
After inspection, repair and/or reassembly, the clamps should be tested using a certified
testing bench.
14
8

OVERHAULING

At least once a year or in case of any damage to the clamp, the clamp should be inspected,
tested and if necessary overhauled by Terrier Lifting Clamps B.V. or by a recognised me-
chanical repair centre. If in doubt consult your supplier.
9

DISPOSAL

Once it the clamp has reached its life cycle end, the clamp can be treated as scrap iron,
provided that the clamp is rendered unfit for further use.
10 TROUBLESHOOTER'S CHECKLIST
Failure/malfunction Possible Cause
Clamp is shifting Clamp not closed
Threaded spindle dirty
Threaded spindle
worn out
Jaws bent open
Load is dirty
Lifting shackle pivoting badly Lifting shackle overloaded Reject clamp
Body bent Clamp overloaded
Lifting shackle oval Clamp overloaded
Shackle pins bent Clamp overloaded
Retaining pins missing Incorrectly assembled
Clamp difficult to open/close Threaded spindle dirty
Threaded spindle bent
Clamp worn out
Clamp contaminated
11

WARRANTY

Terrier Lifting Clamps provides a 5 year warranty on its lifting clamps. This warranty is ap-
plicable to the original end user of the lifting clamps. Only if the clamp has been inspected,
checked and maintained by this instructions and by an official dealer. This warranty period
of 5 years is valid from the day of purchase, and is liable to all conditions and measurements
stated in this document.
11a CONDITIONS
This warranty only covers failures in the lifting tools which is the consequence of production
errors which occur during normal use. The warranty covers no wear to components such
as pivots, cam assemblies, lock springs etc. Should there be any kind of failure within this
guarantee period, the lifting tool will be replaced or repaired to insight of the producer.
Action
Close clamp
Clean spindle
Reject clamp
Reject clamp
Clean load
Reject clamp
Reject clamp
Reject clamp
Fit new retaining pins
Clean spindle
Reject clamp
Reject clamp
Clean clamp
15