Lubrication; Cutting Wheels - DeWalt D36000 Guide D'utilisation

English
1. Loosen the bevel lock knob 41 in the rear of the saw and adjust the head of the saw to
the correct miter degree. The bevel pointer
of adjustment.
2. Always do a dry run and push the cart past the cutting wheel before turning on the saw.
Ensure the cutting wheel is adjusted to the center of the groove.
3. Mark the tile and line the tile against the fence of the cutting cart and the edge guide.
Proceed to make the cut.
4. Turn off the saw.
Fig. AA
Fig. BB
25
54
Moving the Saw (Fig. CC)

CAUTION: Do not attempt to move the saw while filled with water or personal injury
may result.

CAUTION: Always lock cutting cart before moving or transporting saw.
Before moving the saw, be sure the to drain the water pan by placing a 5 gallon (19 liters)
bucket under the drain plug 52 of the saw. Remove the drain plug and allow the water to
empty into the bucket.
Fig. CC
52
MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn unit off and
disconnect it from power source before making any adjustments or removing/
installing attachments or accessories. An accidental start-up can cause injury.
Transportation and Storage (Fig. DD)

WARNING: For your own safety, it is recommended that two people carry this machine or
serious injury could result.

CAUTION: Always lock cutting cart before moving or transporting saw.
The rear water attachments 8 , 9 cutting cart water attachments
may be nested together to make carrying easier (Fig. DD).
8
on the front of the saw will show the angle
42
12 , 13 and water pan
The attachments are numbered 1-4. The attachments must fit in the order shown in Fig. DD
starting with the small cutting cart water attachement
nOTE: The large cutting cart water attachment
stored upside down.
Fig. DD
Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the plastic materials used in these parts.
Use a cloth dampened only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
1. Turn off the saw and disconnect it from the power source.
2. Place a 5 gallon (19 liters) bucket under the drain plug. Remove the drain plug by
loosening the attached wing nut and allow the water to empty into the bucket.
3. Slide the cutting cart off the rail system. Spray the cutting cart with a hose or wipe with a
grout sponge or rag.
4. Wipe the rails with a grout sponge or a rag. Spray lubricants are not required on the guide
rail or wheels.
5. Clean the water reservoir by wiping with a grout sponge.

WARNING: Do not spray with water. Some water may reach the motor area.
Use only mild soap and a damp cloth to clean the tool. Many household cleaners contain
chemicals which could seriously damage plastic. Also, do not use gasoline, turpentine, lacquer
or paint thinner, dry cleaning fluids or similar products. Try not to let any liquid get inside the
tool; never immerse any part of the tool into a liquid.

Lubrication


WARNING: NEVER spray or in any other way apply lubricants or cleaning solvents inside
the tool. This can seriously affect the life and performance of the tool and may result in
personal injury.
D WALT tools are properly lubricated at the factory and are ready for use. However, it is
e
recommended that, once a year, you take or send the tool to a certified service center for a
thorough cleaning and inspection.
Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center. If you need assistance in locating any accessory, please
contact D WALT call 1-800-4-D WALT (1-800-433-9258) or visit our website: www.dewalt.com.
e e
Stand
D24001 Heavy Duty Tile Saw Stand

Cutting wheels

7" (178 mm) DW4760 – Wet Ceramic Tile Cutting Cutting Wheel
7" (178 mm) DW4766 – Wet Porcelain Tile Cutting Cutting Wheel
7" (178 mm) DWA4768 – Wet Glass Tile Cutting Cutting Wheel-
10" (254 mm) DW4761 – Wet Ceramic Tile Cutting Cutting Wheel
15
10" (254 mm) DW4764 – Wet Porcelain Tile Cutting Cutting Wheel
10" (254 mm) DWA4769 – Wet Glass Tile Cutting Cutting Wheel
in order to seat correctly.
12
13 and the small rear water attachment 8
9
8
13
12
15
WALT, have not been tested
e
are