Publicité
Additional Information
Additional Information
It's often easy to mistake incorrect operation for trouble and malfunction of the unit. If you think there is something wrong with the component, check the
points below first. If the problem persists, contact you nearest Pioneer-authorized service center and have them check over the unit.
Symptom
¶ The power cord is unplugged from the wall outlet.
Power cannot be turned on.
¶ The power was turned off from the component (stereo
No sound is heard during
The recorder is not connected up properly.
playback.
¶ The recorder is not connected up properly.
Cannot record.
¶ The
¶ The input selection is incorrect.
¶ The analog
¶ The analog recording level is set too high.
Recorded sound is
¶ Signal connections are incorrect.
distorted.
¶ There is interference from a TV set.
¶ The disc is damaged or warped.
¶ The disc is extremely dirty.
¶ The remote control batteries are exhausted.
Remote control operation is
impossible.
¶ There is an obstacle between the remote control unit and
¶ The remote control unit is being operated outside the
Some tracks are skipped
The
without being played.
Skip playback does not
The
occur.
¶ The disc has not been finalized after recording. When
A recorded CD–R disc
cannot be played on other
CD players.
¶ The pickup lens of the other
The point-of-sale demon-
See page 57 for instructions on how to cancel the store
stration is displayed.
demo mode.
If digital synchro-recording fails to operate correctly, check the following:
1. Pause playback of the source, then press the DIGITAL SYNCHRO button again.
÷ If you're recording from a portable CD player, etc., make sure that the shock-protection feature is switched off.
2. Start playback of the source component once you see the SYNCHRO indicator start to blink.
3. If none of the above solves the problem, use manual digital recording to record.
÷ Digital synchro-recording uses a digital sub-signal contained in the source player's digital output. Digital synchro-recording will not work when
recording from the following devices:
÷ CD players whose digital output does not include a sub-signal
÷ Portable CD, MD or DVD players which do not output a digital signal when stopped.
Cause
amplifier, audio timer, etc.) to which it is connected.
–
or
–
disc in use has already been
CD
R
CD
RW
finalized.
control is set too low.
R E C
R E C
R E C L E V E L
R E C
R E C
L E V E L
L E V E L
L E V E L
L E V E L
main unit.
remote controllable range.
button is set to on.
S K I P
S K I P
P L A Y
P L A Y
S K I P P L A Y
S K I P
S K I P
P L A Y
P L A Y
button is set to off.
S K I P
S K I P
S K I P P L A Y
S K I P
S K I P
P L A Y
P L A Y
P L A Y
P L A Y
such a disc is loaded in the unit, the
lights.
player is dirty, impairing
CD
its ability to play
–
discs.
CD
R
Remedy
¶ Plug the power cord into a power outlet.
¶ Turn on the component supplying the power to the
recorder.
Check all connections, especially to the amplifier—
pp.12–15
¶ Check all connections—pp.12–15
¶ Use a non-finalized disc or erase the
–
disc—pp.54–56
CD
RW
¶ Select the input connected to the source component
you're recording from.
¶ Increase the recording level—p.41
¶ Reduce the analog recording level—p.41
¶ Check all connections—pp.12–15
¶ Turn the
TV
from the
TV
¶ Use another disc.
¶ Clean the disc.
¶ Replace both of the remote control batteries with new
ones.
¶ Remove the obstacle.
¶ Operate in the remote controllable range—p.20
Set the
S K I P
S K I P P L A Y
S K I P
S K I P
S K I P
Set the
S K I P P L A Y
S K I P
S K I P
S K I P
S K I P
¶ Finalize the disc—p.53
–
indicator
CD
R
¶ Try the disc on a different
get the pickup lens on the original player cleaned.
power off or install this unit further away
.
button to off—p.45
P L A Y
P L A Y
P L A Y
P L A Y
button to on—p.45
P L A Y
P L A Y
P L A Y
P L A Y
player. If it plays
CD
OK
then
59
En
Publicité
Chapitres
Dépannage
