Publicité
Additional Information
Additional Information
Troubleshooting
Below is a list of messages mainly related to playback and recording problems, together with a brief explanation and a page reference where you can find
more information:
Display
CHECK DISC
CHECK
(blinking display)
Display messages relating to recording:
Display
CAN NOT COPY
The input signal is digital-copy protected with
SCMS
CAN NOT REC
The digital source was interrupted.
The source is not audio, or is an incompatible
format (e.g. a
CHECK INPUT
The source player was already playing when the
CD ?
DIGITAL SYNCHRO
DIGITAL
DIGITAL
DIGITAL
DIGITAL
SET UP
The unit is preparing to record.
REPAIR
The recorder was switched off/unplugged after
recording without ejecting the disc. The
recorder could not write essential recording
information onto the disc.
REC FULL
No more recording is possible because the
available recording time of the disc has been
used up, or 99 tracks have already been
recorded on the disc.
Pro DISC
The loaded disc is a
professional use without the
U S E
U S E
U S E
U S E
U S E
Display messages relating to playback:
Display
Cause
NEW DISC
A blank disc is loaded.
NO DISC
An attempt is made to start playback without
loading a disc.
The unit is resuming an operation. If the power
RESUME
supply is cut off (either by mistake or due to a
power failure) during recording, the unit enters
resume mode once power is restored so that
additional recording is possible.
58
En
Cause
The disc is damaged or dirty.
The disc is loaded upside down.
A system error occurred, perhaps due to noise
or static electricity.
Cause
.
–
).
CD
ROM
button was pressed.
SYNCHRO
SYNCHRO
SYNCHRO
SYNCHRO
–
or
–
disc for
CD
R
CD
RW
CONSUMER
CONSUMER
CONSUMER
CONSUMER
CONSUMER
disignation.
Remedy
Take out the disc and check for dust, dirt, scratches, etc. Clean
as necessary.
Take out the disc and reload it label-side up.
If the same messages are displayed again after the disc is
reloaded, unplug the power cord and plug it in again. If the
same messages are still displayed, please contact a Pioneer
authorized service center.
Unplug the power cord and plug it in again. If the same
messages are displayed again, please contact a Pioneer
authorized service center.
Remedy
Record the source through the analog inputs.
Check that the digital input cable is connected properly and
that the power of the source player is on.
Check that the source is a regular music source.
Stop the source player. After a short time, 1 -
is displayed, and the recorder goes into synchro–record-pause
mode.
Wait until the message disappears.
While
is displayed, the recorder automatically
REPAIR
REPAIR
REPAIR
REPAIR
REPAIR
examines the recorded area of the disc and updates the track
numbers and recording time data. This process takes about 40
minutes for a fully recorded disc. Finalization or further
recording is possible once the
REPAIR
REPAIR
REPAIR
REPAIR
REPAIR
Use another disc, or erase the
–
CD
RW
Load a
–
or
–
disc that is designated as being for
CD
R
CD
RW
consumer use.
Remedy
Only recording is possible on blank
Playback is not possible.
Open the tray and check that a disc is loaded.
Wait until the message disappears.
Reference
p.11
p.22
Reference
p.40
p.12
1 -
1 -
- - - - -
1 -
1 -
or
SYNC
SYNC
A L
A L
SYNC
SYNC
SYNC
SYNC
SYNC
A L
A L
A L
SYNC
SYNC
SYNC
pp.31–34
message disappears.
disc.
pp.54-56
Reference
–
or
–
discs.
p.22
CD
R
CD
RW
p.22
Publicité
Chapitres
Dépannage
