Special Safety Rules - Metabo SX E 425 TurboTec Mode D'emploi

17026838_0707 SXE Turbo NAFTA.book Seite 6 Dienstag, 10. Juli 2007 11:27 11
ENGLISH
ENG
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use safety equipment. Always wear eye
protection. Safety equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
c) Avoid accidental starting. Ensure the switch
is in the off-position before plugging in. Carrying
power tools with your finger on the switch or
plugging in power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tools operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc., in accordance with these instructions and
6
in the manner intended for the particular type of
power tool, taking into account the working
conditions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

3 Special Safety Rules

Hold powertools by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring or its
own cord. Contact with a „live" wire will make
exposed metal parts of the tool „live" and shock
the operator.
Before using this power tool, carefully read
through and familiarise yourself with all the
enclosed safety information and the instructions.
Keep all enclosed documentation for future refer-
ence, and pass on your power tool only together
with this documentation.
For your own protection and for the
protection of your power tool pay
attention to all parts of the text that
are marked with this symbol!
The dust created when work is in progress can
often be damaging to health (e.g. during
processing of oak and beech wood, stone, metal
and paintwork which can contain lead or other
harmful materials). This dust should not be allowed
to penetrate the body. Use vacuum extraction
appliances and wear suitable masks to provide
additional protection from dust. Remove any accu-
mulation of dust thoroughly, e.g. by vacuuming
with the appropriate special suction unit.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Wear ear protectors when working for long periods
of time. High noise levels over a prolonged period
of time may affect your hearing.
Materials that generate dusts or vapours that may
be harmful to health (e.g. asbestos) must not be
processed.
Secure the workpiece against slipping, e.g. with
the help of clamping devices.
SYMBOLS ON THE TOOL:
....... Class II Construction
V ........... volts
A ........... amperes
Hz ......... hertz