Special Safety Instructions - Metabo RBE 15-180 Mode D'emploi

before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
2.5 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

3. Special Safety Instructions

Hold the power tool by the insulated gripping
surfaces because the abrasive belt may
contact its own cord. Damage to a "live" wire may
energise metal parts of the power tool and cause an
electric shock.
Flying sparks are created when sanding metal.
Ensure that no persons are in danger. Due to the
risk of fire, all combustible materials must be
removed from the work area (area affected by flying
sparks).
During machining, of metals in
particular, conductive dust can form
deposits inside the machine. This can lead to the
transfer of electrical energy onto the machine
housing. This can mean a temporary danger of
electric shocks. This is why it is necessary when the
machine is running to blow compressed air through
the rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
We recommend using a stationary extractor system
and connecting a residual current circuit-breaker
(FI) upstream. When the machine is shut down via
the FI circuit-breaker, it must be checked and
cleaned. See chapter 7. Cleaning for more
information on cleaning the motor.
Wear ear protectors. Exposure to noise can cause
hearing loss.
Wear protective gloves.
WARNING – Always wear protective
goggles.
Secure the workpiece against slipping, e.g. with the
help of clamping devices.
Always guide the machine with both hands on the
handles provided. Loss of control can cause
personal injury.
Never place your hand near rotating parts of the
device or near the rotating sanding belt.
Remove sanding dust and similar material only
when the machine is not in operation.
Pull the plug out of the plug socket before any
adjustments, conversions or servicing are
performed.
The rated speed of the sanding belt must be at least
equal to the belt speed in idling marked on the
power tool. A sanding belt running faster than its
rated speed can break and fly apart.
Check prior to each use that the sanding belt is
correctly attached and is completely on the rollers.
Carry out a trial run: Allow the machine to run at
idling speed for 30 seconds in a safe location. Stop
immediately if significant vibrations occur or if other
defects are noted. If such a situation occurs, check
the machine to determine the cause.
Additional Warnings:
Some dust created by power
WARNING
sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
SYMBOLS ON THE TOOL:
....... Class II Construction
V .......... volts
A .......... amperes
Hz ........ hertz
~
.......... alternating current
n ......... no load speed
0
../min ... revolutions per minute
rpm ..... revolutions per minute
B ........ sanding belt length
L
ENGLISH en
California Prop 65 08_2018
5