AEG POWERTOOLS BLK1218 Notice Originale page 6

SPECIFIED CONDITIONS OF USE
The charger is intended to charge AEG System GBS
batteries from 12 V to 18 V and AEG System PCLS
batteries 12 V.
Do not use this product in any other way as stated for
normal use.
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
BATTERIES
New battery packs reach full capacity after 4 - 5 chargings
and dischargings. Battery packs which have not been used
for some time should be recharged before use.
For an optimum life-time, the battery packs have to be fully
charged, after use.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
CHARACTERISTICS
First battery installed, fi rst charged. Once the fi rst battery is
charged, the charger switch automatically and charges the
second one.
If two battery packs installed before charger power built,
12-18V GBS platform port fi rst priority to charge once power
built.
After inserting the battery into the reception of the charger
the battery will be analysed within 10 seconds and then
automatically be charged.
When a hot or cold battery pack is inserted into the charger,
charging will begin automatically once the battery reaches
the correct charging temperature (0°C...50°C).
Charging time varies depending on the battery temperature,
charge needed and the type of battery pack being charged.
As soon as charging is completed, the charger switches
over to "trickle" charge to maintain the full capacity.
If green lamp illuminates, either the battery has not
been completely mounted or there is a fault in the battery or
the charger. For safety reasons you must stop using the
charger and battery immediately and have them inspected
by an AEG Customer Service Centre.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
10 ENGLISH
Check with forwarding company for further advice
MAINTENANCE
If the supply cord of this appliance is damaged, it must only
be replaced by a repair shop appointed by the manufacturer,
because special purpose tools are required.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
Do not burn used battery packs.
Never charge a damaged battery pack.
Replace with a new one.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached the
end of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
This tool is only suitable for indoor use. Never
expose tool to rain.
Class II tool.
Time-lag fuse 3.15 A
T3.15A
Time-lag fuse 15 A
T15A
European Conformity Mark
National mark of conformity Ukraine
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
EurAsian Conformity Mark.
TECHNISCHE DATEN LADEGERÄT
Spannungsbereich..................................................................
Ladestrom Schnellladung .......................................................
Gewicht nach EPTA-Prozedur 01/2003 ..................................
Empfohlene Umgebungstemperatur beim Laden ...................
LED 12-18 V GBS
Grün Grün Rot
Standby aus aus aus
Analyse aus aus aus
Laden aus aus aus
Voll geladen aus aus aus
Erhaltungsladung
Standby aus aus aus
Erhaltungsladung
Zu warm aus aus aus
Zu kalt
Defekt aus aus aus
DC Überspannung aus aus aus
(kein Aufl aden
10V < / > 15,5V)
LED 12 V
Grün Grün Rot
Standby aus aus aus
Analyse blinken aus aus
Laden ein blinken aus
Voll geladen ein ein aus
Erhaltungsladung
Standby ein ein...aus aus
Erhaltungsladung
Zu warm ein aus aus
Zu kalt
Defekt ein aus ein
DC Überspannung aus aus aus
(kein Aufl aden
10V < / > 15,5V)
BLK1218
................. 12-18 V
............... max. 5 A
................... 1,45 kg
............. +5...+40 °C
Rot Grün Grün Rot
aus ein...aus aus aus
aus ein aus aus
aus ein aus
blinken
aus ein ein aus
aus aus
ein ein...aus
aus ein aus aus
aus ein aus ein
aus blinken aus aus
Rot Grün Grün Rot
aus ein...aus aus aus
aus ein aus aus
aus ein aus aus
aus ein aus aus
aus aus aus
ein
On ein aus aus
aus ein aus aus
aus blinken aus aus
DEUTSCH
Rot Grün
aus aus
aus blinken
aus ein
aus ein
aus ein
ein ein
aus ein
aus aus
Rot Grün
aus aus
aus aus
aus aus
aus aus
aus aus
aus aus
aus aus
aus aus
11