Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
screwed onto the workbench or the
frame.
•
Fig. C shows the part to be sawn out (310 x
310 mm), so that the sawdust can fall through
it and piling up is prevented!
Only if you do not use an extraction system!
•
Fasten the machine with bolts.
If the frame is used, it must be fixed on the
floor with four screws and the machine must
be fixed on the frame with four screws. Check
the screws before switching the machine on.
Assemble undercarriage
Fig. F
•
Turn the machine upside down.
•
Remove the black plastic bottom plate by
unscrewing the 6 screws. (Fig. F-1).
•
Unscrew the adjusting knob on the front and
tilt the motor (Fig. F-2), then remove the
transport packing (Fig. F-3).
•
Now place one by one the uprights in the
casing of the sawing bench (Fig. F-4).
•
Secure the uprights with 4 screws using a
screwdriver, do not completely tighten the
screws (Fig. F-5).
•
Fit the 4 support bars, do not completely
tighten the screws (Fig. F-6)
•
Fit the black plastic bottom plate and screw it
tight.
•
Attach the rubber feet under the uprights (Fig.
F-7).
•
Turn the machine into an upright position on a
flat surface and adjust the machine so that it
stands in a stable position, tighten all the nuts
and bolts (Fig. F-7).
Assemble bracket/push stick
•
Attach the 2 brackets onto the casing of the
sawing bench and screw them tight (Fig. F-8).
•
Place the push stick in the brackets.
Assembly and attachment of the rip fence
Fig. D
•
Attach the aluminium fence (A) to the
positioning block (B).
•
Now you can attach the complete rip fence to
the bench top.
•
Slide the rip fence via one end of the
positioning rail (C) over the bench top.
•
Adjust the position of the aluminium fence
profile (A) such that the end corresponds to
the rear edge of the saw.
Assembly of the riving knife and the
protective cap
Fig. E
•
Turn the saw blade completely upwards.
•
Remove the bench inlay.
•
Assemble the riving knife on the set-up for this
purpose and use hereby the Allen screws and
the filling rings. Ensure that the riving knife
falls properly into the opening (= groove).
•
Now put the inlay back in the bench and fasten
it.
•
Now assembly the protective cap onto the
riving knife and use hereby the profiled nut
and self-locking nut.
Now lay a lath against the saw blade
and the riving knife and check whether it
falls properly into the extension of the
saw blade. If this is not the case: Loosen
the fastening bolts and place or remove
the filling rings.
•
Above the saw table the radial distance
between the riving knife and the toothed rim of
the saw blade shall not at any point exceed 5
mm at the depth of cut set.
•
The tip of the riving knife shall not be lower
than 5 mm from the tooth peak, as shown.
Assembly of the saw blade
First remove the plug from the mains
before the saw blade is assembled or
replaced.
•
Remove the inlay from the bench. Use a
screwdriver for this purpose.
•
Turn the saw axle completely upwards.
Remove the nut and the outside flange from
the saw axle.
•
Now slide the saw blade over the saw axle
and now put the outside flange and the nut
back. Tighten the nut by hand.
•
Now use the 2 keys: one for the flange and
one for the nut and now clamp it.
•
Now put the inlay back in the bench and fasten
it.
Mounting the push stick holders
Mount both push stick holders on the side of the
machine using the bolts and rings supplied.
Use of the mitring set-up
Fig. A
By turning the handle at the side of the machine
9
Publicité
Table des Matières
