Maytag MAT20CSAGW Instructions D'installation page 19

Lave-linge commercial
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

ELECTRONIC CONTROLS SET-UP INSTRUCTIONS
CODE
H.00
EXTRA RINSE Upgrade Price - Increase or decrease between 0
EXTRA
and 200 by pressing the POWERWASH or TEMPERATURE key
RINSE
pad. Factory preset for 1 coins = $0.25.
g Press the NORMAL key pad once to advance to next code.
COIN/DEBIT OPTION
J.Cd
J.Cd
Both coin & debit selected.
J.C_
Coins selected, debit disabled. Press the DELICATES key pad
3 times for this selection.
J._d
Debit Card selected, coins disabled. Press the DELICATES key
pad 3 times for this selection.
J.Ed
Enhanced Debit is self-selected when a Generation 2 card reader
is installed in the washer. The Ed option cannot be manually
selected or deselected.
g Press the NORMAL key pad once to advance to next code.
L.00
PRICE SUPPRESSION OPTION
This option causes the customer display to show 'ADD' or
'AVAILABLE' rather than the amount of money to add. (Used
mainly in debit installations.)
L.00
Not Selected 'OFF'.
L.PS
Selected 'ON'. Press the DELICATES key pad once for this
selection.
g Press the NORMAL key pad once to advance to next code.
CLEAR ESCROW OPTION
n. CE
When selected, money held in escrow for 30 minutes without
further escrow or cycle activity will be cleared.
n. CE
Selected 'ON'.
n. 00
Not selected 'OFF'. Press the DELICATES key pad once to
deselect this selection.
g Press the NORMAL key pad once to advance to next code.
COIN (HUNDREDTH) INCREMENT OFFSET
U.00
U.00
For use with card reader applications only.
g Press the NORMAL key pad once to advance to next code.
A3.03
NORMAL Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specific settings. Normal is set to 03 from the
factory.
A4.01
DELICATES Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specific settings. Delicates is set to 01 from the
factory.
A5.1C
POWERWASH Cycle Settings. Allows the owner to select the
cycle default options of Water Temperature, Soil Level, and Extra
Rinse.
See Table 1 for specific settings. Powerwash is set to 1C from the
factory.
A6.03
NORMAL ECO Cycle Settings. Allows the owner to select the
cycle default options of Water Temperature, Soil Level, and Extra
Rinse.
See Table 1 for specific settings. Normal Eco is set to 03 from the
factory.
EXPLANATION
If cycle counter (9.0C) is selected, the following is true:
1 xx Number of cycles in THOUSANDS.
2xxx Number of cycles in ONES.
This is "VIEW ONLY" and cannot be cleared.
Press the NORMAL key pad once to advance
to next code.
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 xx Number in THOUSANDS.
4xxx Number in ONES.
5 xx Number of HUNDRETHS.
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
PD Models: Reinstall access door.
n
If preferred, just wait through 2 minutes of inactivity. All settings
will be saved and the display will revert to Select Cycle screen.
Table 1
A3, A4,
Extra
Soil Level
Water
A5, A6
Rinse
(Heavy-On,
Temp
Normal-Off)
00
Off
Off
01
Off
Off
02
Off
Off
03
Off
Off
Warm
04
Off
Off
08
Off
On
09
Off
On
a
Off
On
B
Off
On
Warm
C
Off
On
Technician Service Access Code
This method is only available on PR washers set to free vend
(6 00).
To enter service mode:
Press the POWERWASH, EXTRA RINSE, TEMPERATURE, and
DELICATES key pads within 10 seconds.
To exit service mode:
Wait 2 minutes without touching any key pads (without diagnostic
modes running)
or
Power down the washer, then reapply power.
NOTE: If a service cycle is in progress upon exiting service mode,
the cycle will complete normally with cycle status information
displayed. The display will resume normal customer operation
mode when the cycle ends.
1 02 = 2,000
2225 =
TOTAL CYCLES = 2,225
3 01 = $1,000.00
4600 = $ 600.00
5 75 = $
TOTAL = $1,600.75
A3, A4,
Extra
Soil Level
A5, A6
Rinse
(Heavy-On,
Normal-Off)
Tap
10
On
Off
Cold
Cold
11
On
Off
Cool
12
On
Off
13
On
Off
Hot
14
On
Off
Tap
18
On
On
Cold
Cold
19
On
On
Cool
1A
On
On
1B
On
On
Hot
1C
On
On
225
00.75
Water
Temp
Tap
Cold
Cold
Cool
Warm
Hot
Tap
Cold
Cold
Cool
Warm
Hot
19

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mat20mnagwMat20pdagwMat20pnagw

Table des Matières