Sharpening The Blades; Initial Settings - Sammic CK-35V Mode D'emploi

EN

SHARPENING THE BLADES

WARNING: The discs (A), grids (B) and blade assembly (T) have very
sharp edges and must be handled with extreme care.
The disc blades (A) and blade assembly (T) can be removed easily for
sharpening. Always use soft stone to avoid damaging the blades' cutting
angle.
TROUBLESHOOTING
The machine fails to start on pressing "Start" (A) when it is ready for
operation and the message indicating the action to be performed appears on
the display. The associated sensor may not be working.
- Check that all of the components are in position.
- There is a problem with one of the safety devices if the problem persists.
Call a SAMMIC authorised technical service.
- The screen fails to turn on: The flat cable that connects the power and
control boards is loose or damaged or the electronic control panel is faulty.
- To verify that the keypad is working properly, press the keys with an
accessory fitted and verify that the plate emits a beep and the display is
activated. Otherwise, change the keyboard.
- The machine was running and stopped without any key being pressed.
If the machine is running it will stop automatically after 30 minutes without
human intervention.
In the Vegetable Cutting mode the motor will not start when the plunger (M)
is in the lowered position.
- Press "Start" (7) again to reset the cutter IF the plunger (M) is left open for
more than 30 seconds.
- On the CK-35V/38V/45V/48V and CA-3V/4V the hopper may be too full
and the plunger (M) may not activate the microswitch. Reduce the amount of
product in the hopper and try again.
- The disk (A) or the blade assembly (C) may be rubbing on another part if
the machine is excessively noisy. The main shaft bearings have probably
deteriorated.
The unit has its own protection devices that are activated when damage
to important components is likely. These protections are represented by
a red triangle (1) and a circle (2) lit simultaneously with the explanatory
text. Display of these indicators does not mean that the equipment has
been damaged but it has detected a status that triggers the programmed
protection. Press Start (A) again to reset the protection system. Contact the
authorised SAMMIC technical service if the alert persists and does not permit
normal operation of the machine. These alerts are recorded in a log that can
be consulted.
In addition to the FORCE CONTROL function that enables users to monitor
the status of the motor, it is also possible to display some of the machine's
parameters while it is running. Pressing and holding the up and down keys
simultaneously will display four numbers that indicate the following (from left
to right): Motor intensity, motor power, IGBT module temperature and the
internal temperature of the machine.
Motor intensity: Tenths of an Ampere
Motor power: W
IGBT temperature: ºC
Internal temperature: ºC
If any of the alerts persists or if the values indicated in the manual are
exceeded, check and asses if the work being done is proportional and try
to adjust it in load and rest period to keep the parameters within the proper
ranges to avoid tripping the protections. If you consider that the machine is
at fault, contact Sammic's authorised technical service.

INITIAL SETTINGS

Pressing the following keys with the machine turned on enables the following
functions
PRESS (B): Enables selection of the language of the messages the machine
displays. Select the language using the up (D) or down (E) keys and press
Start (A) or disconnect the machine to quit.
BACK ARROW (C): Accesses the counters that record the level of use of the
machine. Pressing up (D) and down (E) displays:
0 HPOW: Hours connected to power supply.
1 HCUT: Hours with motor running in Cutter mode.
2 HCOR: Hours with motor running in Vegetable Cutting mode.
3 NARR: Number of motor starts.
4 NMTERM: Number of motor thermal manoeuvres.
5 NMCIER: Number of bayonet closing manoeuvres.
6 NMTAPA:: Number of manoeuvres of the vegetable cutting lid.
7 NMPCA: Number of manoeuvres of the vegetable cutter plunger and the
cutter lid.
Press and hold the Start/Stop button for 3 seconds to reset the counters.
TIMER (F): Turns on all the screen's icons.
DOWN (E): The panel version is shown.
UP (D): The program version is shown.
18