Sammic CK-35V Mode D'emploi page 15

CLEANING
- Disassemble and clean the machine at the end of each day or each time
you change the product or accessory.
- All components in contact with the food must be cleaned immediately after
use using hot water and a food-safe detergent. Then rinse with abundant hot
water and disinfect using an ethyl alcohol-soaked cloth (90º).
- DO NOT use abrasive detergents (nitric acid, neat bleach, etc.) or non-
stainless steel scourers or scrubbers. They may cause the machine to rust.
- The removable parts of the CK and CA should not be washed in a
dishwasher. The detergents can damage the surface finish.
- DO NOT clean the outside of the machine with a direct stream of water. Use
a damp cloth and any common detergent for cleaning.
MAINTENANCE
- Regularly check that the machine's safety devices are working properly.
Call the SAMMIC authorised technical service if you detect any anomaly.
- Regularly inspect the drive shaft seal to ensure that the surrounding area
is properly protected. Installing a new seal is recommended every time the
drive shaft is loosened for maintenance.
- If the power cable is damaged, a new one must be installed before the
machine is used again. Only a SAMMIC authorised technical service may
perform this replacement.
The noise level in operation is less than 70 dB(A) with the machine placed at
a height of 1.6 m and a distance of 1 m. Background noise: 32dB (A).
FUNCTIONS AND OPERATION OF THE ELECTRONIC
CONTROL
ON/OFF (14)
Starts the motor if none of the safety devices impedes it. Pressing a second
time stops the motor.
PRESS (15)
Only in Cutter mode. The motor starts and runs as long as this key is held
down and stops when it is released.
The language selection menu is accessed during the first 3 seconds when
this key is pressed.
REVERSING (16)
Pressing this key in cutter mode for 3 seconds accesses the SENSO
FORCE function. SensoForce enables the user to adjust the level at which
the acoustic alert indicates that the plunger has reached the desired force.
In Cutter mode, pressing this key changes the rotation direction of the motor.
This can be done with the motor running or stopped.
The counters that record the work level of the machine are accesses during
the first 3 seconds when the key is pressed.
INCREASE (11)
Each time the key is pressed the setting on the display increases. The
program version of the power panel appears in the first 3 seconds.
DECREASE (12)
Each time the key is pressed the setting on the display decreases. The
program version of the control panel appears in the first 3 seconds.
TIMER (13)
Only in cutter mode. Pressing activates the countdown function. After
selecting the time, a second press confirms the selection.
OPERATION
Two lines are displayed in the centre of the screen (1) when the machine is
switched on. Icon number 7 (representing a cutting disk) is displayed if the
"Vegetable Cutter" accessory is mounted and Icon number 5 (representing
a rotor) is displayed if the "Cutter" is mounted. This shows that the control
panel has identified each attachment. The speed level and the associated
RPM are also displayed.
Speed levels from 1 to 10 can be selected in Cutter mode and from 1 to 5 in
"Vegetable Cutter" mode.
- Time control: Only available in "Cutter" mode. The countdown time and
automatic shut-down can also be set.
The appropriate informative text will appear on the screen if "Start" is pressed
while any of the safety devices out of position.
START-UP AND GENERAL OPERATION
"Vegetable Cutter" operating mode (CK-35V/38V, CA-3V/8V).
With the machine disconnected from the mains:
- With the bayonet mechanism (Y) open (AA), place the "Vegetable Cutter"
accessory on the motor block so that the three lugs are inserted into the
holes of the quick-lock mechanism. Close (Z) the bayonet mechanism (Y) to
lock the accessory on the motor block.
- The hinged cover (J) on the CK-35V/38V and CK-45V/48V must be fitted
as indicated in the drawings and secured with the pin (O).
- The plunger (M) on the CK-35V/38V must be placed as indicated in the
drawings and secured with the pin (N).
- If you wish to use the tube head with the CK-35V/38V and CK-45V/48V, it
must be placed as indicated in the drawings and secured with the pin (O).
Fitting the disks (A) and grids (B)
- Open the lock (I) and open the hinged lid (J).
- Place the ejector (C) in its housing in the dive shaft.
- The grid (B) is inserted into the cavity in the lower cover (D) when the
process so requires.
- Fit a disk (A) on the drive shaft. To do so, insert the disk (A) onto the drive
shaft and turn it clockwise until it engages with the shaft.
- On the CK-45V/48V and CA-4V, thread the bit (Q) or the mixer (R) -
depending on the product to be cut - onto the drive shaft.
Close (J) and lock (I) the hinged cover.
15
EN