Important Safety Information - Hatco Glo-Ray GR Série Manuel D'installation Et D'utilisation

Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
WARNING
ELECTRIC SHOCK HAzARD:
• Units supplied without an electrical cord and plug require a
hardwired connection to the on-site electrical system.
Connection must be properly grounded and of the correct
voltage, size, and configuration for the electrical specifications
of the unit. Contact a qualified electrician to determine and
install the proper electrical connection.
• Plug unit into a properly grounded electrical receptacle of the
correct voltage, size, and plug configuration. If plug and
receptacle do not match, contact a qualified electrician to
determine and install proper voltage and size electrical
receptacle.
• Turn OFF power switch, unplug power cord/turn off power at
circuit breaker, and allow unit to cool before performing any
cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged or
saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use jet-clean
spray to clean this unit.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power cord.
Cord must be replaced by Hatco, an Authorized Hatco Service
Agent, or a person with similar qualifications.
• Use only Genuine Hatco Replacement Parts when service is
required. Failure to use Genuine Hatco Replacement Parts will
void all warranties and may subject operators of the
equipment to hazardous electrical voltage, resulting in
electrical shock or burn. Genuine Hatco Replacement Parts
are specified to operate safely in the environments in which
they are used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to operate
safely in Hatco equipment.
FIRE HAzARD:
• Locate unit the correct distance from combustible walls and
materials. If safe distances are not maintained, discoloration
or combustion could occur. Refer to specific installation and
mounting information in this manual for proper clearances.
• Make sure to follow the installation information listed below for
specific strip heaters. If safe distances are not maintained,
discoloration or combustion could occur.
a. Do not install standard wattage strip heaters (GR, GRA,
GRN, GRL, GRAL Series) less than 254 mm (10") above
combustible surfaces.
b. Do not install high wattage strip heaters (GRH, GRAH,
GRNH, GRHL, GRAHL Series) less than 343 mm (13-1/2")
above combustible surfaces.
c. Do not install dual strip heaters (GR-XXD, GRA-XXD,
GRH-XXD, GRAH-XXD, GRL-XXD, GRAL-XXD, GRHL-XXD
and GRAHL-XXD Series) above combustible surfaces.
d. Install all single strip heaters with a minimum distance of
76 mm (3") from a combustible wall or adjacent surface.
Use only light bulbs that meet or exceed National Sanitation
Foundation (NSF) standards and are specifically designed for food
holding areas. Breakage of light bulbs not specially-coated could
result in personal injury and/or food contamination.
Form No. GRCEM1-1115

IMPORTANT SAFETY INFORMATION

EXPLOSION HAzARD: Do not store or use gasoline or other
flammable vapors or liquids in the vicinity of this or any other
appliance.
This unit is not intended for use by children or persons with
reduced physical, sensory, or mental capabilities. Ensure proper
supervision of children and keep them away from the unit.
Make sure all operators have been instructed on the safe and
proper use of the unit.
Make sure food product has been heated to the proper food-safe
temperature before placing under unit. Failure to heat food
product properly may result in serious health risks. This unit is for
holding pre-heated food product only.
For installation with chains, make sure the chains have sufficient
strength and are securely fastened to both the strip heater and the
mounting location. Poorly installed chains may cause the heater to
loosen and fall. Do not place anything on top of heaters installed
with chains.
This unit has no "user-serviceable" parts. If service is required on
this unit, contact an Authorized Hatco Service Agent or contact
the Hatco Service Department at 414-671-6350 or International fax
414-671-3976.
BURN HAzARD: Some exterior surfaces on the unit will get hot.
Use caution when touching these areas.
Standard and approved manufacturing oils may smoke up to 30
minutes during initial startup. This is a temporary condition.
Operate unit without food product until smoke dissipates.
Strip heaters equipped with incandescent lights that require a
circuit breaker larger than 20 amps for the heat element must have
a separate circuit breaker for the incandescent lights that is 20
amps or less.
Ensure safe and proper operation. Refer to the "Minimum
Clearance Requirements" listed in the Installation section of this
manual.
Installation of two or more separate units with less than
76 mm (3") between housings may result in premature failure of
component parts. Failure to provide proper spacing may result in
heat damage to electrical components.
Units are voltage-specific. Refer to specification label for electrical
requirements before beginning installation.
Do not add a decorative soffit to hide a pass-through mounted strip
heater. Excessive heat can cause unit failure.
To prevent premature failure of components due to excessive heat,
remote mounted control switches must be installed outside the
strip heater heat zone.
Damage to countertop material caused by heat generated from
Hatco equipment is not covered under the Hatco warranty. Contact
the manufacturer of the countertop material for application
information.
Use non-abrasive cleaners and cloths only. Abrasive cleaners and
cloths could scratch the finish of the unit, marring its appearance
and making it susceptible to soil accumulation.
3
WARNING
CAUTION
NOTICE