Technical Data; Noise/Vibration Information; Delivery Scope - Bosch GCD 12 JL Professional Notice Originale

OBJ_BUCH-1938-003.book Page 20 Friday, December 16, 2016 9:57 AM
20 | English
27 Upper fastening screw
(cover plate/retracting blade guard)
28 Guide bolt
29 Hex socket screw for mounting of saw blade
30 Clamping flange
31 Saw blade
32 Interior clamping flange
33 Angle display

Technical Data

Metal Cutting Saw
Article number
Rated power input
No-load speed
Soft starting
Laser type
Laser class
Divergence of laser line
Weight according to EPTA-Procedure 01:2014
Protection class
Permissible workpiece dimensions (maximum/minimum) see page 22.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter

Noise/Vibration Information

Sound emission values determined according to
EN 61029-2-10.
Typically the A-weighted noise levels of the product are:
Sound pressure level 100 dB(A); Sound power level
113 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029-2-10: a
2
K=1.5 m/s .
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
1 609 92A 340 | (16.12.16)
34 Scale for miter angles
35 Adjustment screw for laser position
(parallelism)
36 Screw for angle display
37 Laser beam outlet
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
mrad (full angle)
nificantly reduce the exposure level over the total working pe-
riod.
mm 305
Identify additional safety measures to protect the operator
mm 1.8–2.5
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
mm 25.4
terns.
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.

Delivery Scope

Carefully remove all parts included in the delivery from their
packaging.
2
=3.5 m/s ,
h
Remove all packaging material from the machine and the ac-
cessories provided.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Metal cutting saw with mounted saw blade
– Hex key/cross-head screwdriver 12
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
GCD 12 JL
3 601 M28 0.. 3 601 M28 060
W 2000
-1
min 1500

nm 650
mW < 0.39
1M
1.0
kg 20
/II
Bosch Power Tools
1650
1500

650
< 0.39
1M
1.0
20
/II