Deleting A Recording; Adjustments Via The Osd Menu; Displaying Free Memory Capacity - Monacor DMR-123LCD Mode D'emploi

it is possible to change to the previous or following
screen page.
4) Start the reproduction of the selected recording
with the button . If no reproduction has been
started, the recorder switches back to the present
video source after a certain time.
To stop the reproduction of video sequences,
press the button
serted. To continue the reproduction, press the but-
ton again.
To reproduce video sequences at double speed,
press the button
press it twice for fourfold speed (symbol insertion
). By pressing the button
speed is selected again, by pressing the button
the standard reproduction is selected.
To reproduce video sequences backwards at
double speed, press the button
insertion ), press it twice for fourfold speed back-
wards (symbol insertion
ton again, the double speed is selected again,
by pressing the button
tion is selected.
Adjust the reproduction volume for the internal
speaker or a connected monitor with the buttons
and (5). When pressing one of the buttons, the
symbol and the present volume adjustment "00"
to "64" are displayed.
While reproducing, it is possible to go to the
previous or following recording with the buttons
and .
5) To stop the reproduction and to return to the over-
view, press the button
sequence was reached or an individual picture was
shown while reproducing, it is also possible to
change to the overview with the button
As a standard setting, the reproduction is always
stopped at the end of a sequence. For continuous
reproduction of all recordings, while reproducing (or
with the reproduction stopped, symbol insertion
is possible to change to another reproduction mode by
pressing the button
inserted in the picture:
AUTO: all recordings are successively reproduced,
individual pictures are shown for approx. 5 s; the
reproduction stops after the recording by which the
reproduction was started, has been reproduced once
again
LOOP: all recordings are successively and con-
tinuously repeated
STOP: only the selected recording is reproduced
(standard setting with each manual start of a repro-
duction)

5.5 Deleting a recording

To delete a recording selected in the overview (yellow
frame) or which is just reproduced, press the button
(4). Then the following insertion appears on the
screen:
; the symbol (pause) is in-
once (symbol insertion
again, the double
once (symbol
). By pressing the but-
, the standard reproduc-
(2). If the end of the video
.
(7) [repeatedly]. The mode is
YES
Select with the button
ing is to be deleted (YES) or not (NO) [the present
selection is shown in a flashing way] and confirm with
the button (9). To delete all recordings at the same
time, call the OSD menu (⇒ Chapter 5.6.2).
),

5.6 Adjustments via the OSD menu

1) Before the OSD menu can be called, switch the
recorder to direct display of a video source, i. e.
,
stop a present recording or reproduction and exit
the overview [button
2) Press the button
displayed:
MENU SETUP
SYSTEM
FUNCTION
Select a menu item [the present selection is shown in
a flashing way] with the buttons
the corresponding submenu with the button
SYSTEM SETUP
CAPACITY
DELETE
DATE TIME
BEEP
FUNCTION SETUP
MOTION DETECT
OVERWRITE
CAPTURE MODE
) it
A menu can be exited at any time with the button
no button is pressed for approx. 10 s, the menu will be
automatically extinguished.
The menu items available will be described below.

5.6.1 Displaying free memory capacity

DISPLAY CAPACITY
ON
OFF
With the option ON, while recording and with directly
shown video source, the configuration of the memory
card is shown as a bar graph in the lower section of the
picture. If more than
free, the indication is green. If less than
available, the bar graph turns yellow, if it is less than
1 / , the bar graph turns red.
8
DELETE
NO
or (6) whether this record-
(2)], if required.
(4). The following main menu is
and
1 / space of the memory is still
4
GB
(8) and call
(9).
. If
/ space is
1
4
13