Remote Release; Power Supply; Operation; Switching The Recorder On And Off - Monacor DMR-123LCD Mode D'emploi

recording time to be expected of the video sequences
GB
or the number of the individual pictures (photos) which
can be memorized with corresponding memory capa-
city. The actual recording time depends on the com-
plexity of the picture contents, their frequency of
changing and the resulting compression ability of the
files and may therefore deviate from these standard
values. If e. g. a range is monitored in which changes
rarely occur the recording time can also be a multiple
of the time indicated.
Capacity of the
memory card
256 MB
512 MB
1 GB
2 GB
As shown in fig. 2, insert the memory card into the slot
(11) until it locks into place. To be able to record on the
card, the write protect tab at the card must not be in
position LOCK. To remove the card, first press it
slightly into the slot; then it is slightly pushed out by a
spring and can thus easier be seized for pulling it out.

4.3 Remote release

If required, connect the plug (26) of the remote release
(fig. 5) to the jack (21) on the recorder for the remote
release of the function "Capture" (⇒ chapter 5.3).

4.4 Power supply

The power can be supplied via the plug-in power sup-
ply unit, the car adapter, or the integrated battery.
For mobile operation of the recorder, prior to the
first use, recharge the battery at least 8 h with the
recorder switched off [switch Power (20) in position
"Off"]. For this purpose connect the recorder to the
230 V mains or to the 12 V power supply of a car.
For the operation at the 12 V power supply of a car
connect the low voltage plug of the car adapter to the
jack DC 5 V (18) and connect the adapter to a corre-
sponding socket of the electric system of the car.
For the operation at the 230 V mains connect the
low voltage plug of the power supply unit to the jack
DC 5 V (18) and the power supply unit to a socket.
The infrared remote control is supplied with insert-
ed battery. Prior to the first use remove the insulation
strip from the battery compartment.

5 Operation

5.1 Switching the recorder on and off

Switch on the unit with the switch Power (20) [position
"On"]; the power indication (16) lights up. After opera-
tion and for charging the battery switch off the unit
(position "Off").
12
Recording time Max. number of
individual pictures
30 minutes
60 minutes 11 600
120 minutes 23 200
240 minutes 46 400

5.2 Recording video sequences

Note: Prior to the first recording it is recommended to
set the date and time correctly so that the recordings
can better be assigned subsequently. (⇒ Chapter
5.6.3)
1) Select the desired source with the button
The present source is displayed for a few seconds
(VIDEO1 or VIDEO2).
2) To start the recording, press the button
While recording, the symbol
LED REC. (15) flashes.
3) To stop the recording, press the button
5 800
4) If the memory card is full and the option "Overwrite"
has not been selected in the adjustments for the
unit (⇒ chapter 5.6.6), the recording stops, a signal
sounds, and FULL is displayed. To stop the signal,
press the button
If the option "Overwrite" has been selected, the
recording is continued and a signal sounds in each
case when overwriting a previous recording.
The recordings are memorized on the card as individ-
ual files in the ASF format (video with sound). While
recording, approx. every 10 minutes a new file is auto-
matically memorized, the same happens when the sig-
nal source is switched over with the button
the monitor is switched over with the button
5.3 Releasing the "Capture" recording
1) Select the desired source with the button
The present source is displayed for a few seconds
(VIDEO1 or VIDEO2).
2) To release the capture recording, press the button
(10) or the button (25) at the remote release.
While recording, the symbol
display, the LED Capture (14) lights up, and when
using the remote release (25) a signal sounds if this
has been permitted in the adjustments for the units.
Depending on the adjustments in the OSD menu
(⇒ chapter 5.6.7) the capture recording is memorized
as a picture file (symbol insertion
mat or as a short video sequence (symbol insertion
with sound in the ASF format.

5.4 Reproduction

1) Select with the button
tion is to be made on the LCD (1) or a connected
monitor.
2) Press the button
recordings with 9 preview pictures per screen page
is shown on the display (or monitor). The record-
ings are assorted according to the time of record-
ing, starting with the oldest. The preview pictures
with the symbol
video files, the preview pictures of the picture files
do not show a symbol.
3) Select the recording to be reproduced with the but-
tons
ed preview picture. With the buttons
.
(3) whether the reproduc-
(9) so that the overview of the
are the starting pictures of the
and (6). A yellow frame marks the select-
(2).
(7).
is displayed and the
again.
(2) or
(3).
(2).
or appears in the
) in the JPEG for-
)
and (8)