Publicité
Liens rapides
Owner's Instruction and Operation Manual
Model Number:
5501S
Report Number: F19-549
Certified to ASTM E1509-12 (2017)
and Certified to CAN/ULC S627:2023
Mobile Home / Transportable Building
Approved
* All Pictures In This Manual Are For Illustrative Purposes Only. Actual Product May Vary.
Save These Instructions In A Safe Place For Future Reference.
SAFETY NOTICE: If this heater is not properly installed, a house fire may result. For
your safety, follow the installation instructions. Never use make-shift compromises
during the installation of this heater. Contact local building or fire officials about
permits, restrictions and installation requirements in your area. NEVER OPERATE
THIS PRODUCT WHILE UNATTENDED.
CAUTION! Please read this entire manual before you install or use your new room
heater. Failure to follow instructions may result in property damage, bodily injury, or
even death. Improper Installation Will Void Your Warranty!
U.S. Environmental Protection Agency
Certified to comply with 2020 particulate
emissions standards.
THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE.
© 2023 United States Stove Company, 227 Industrial Park Rd., South Pittsburg, TN 37380
R
CALIFORNIA PROPOSITION 65 WARNING:
This product can expose you to chemicals including carbon
monoxide, which is known to the State of California to cause
cancer, birth defects, and/or other reproductive harm. For
more information, go to www.P65warnings.ca.gov
852473N-1603M
Ph. 800-750-2723
Publicité
Manuels Connexes pour United States Stove 5501S
Sommaire des Matières pour United States Stove 5501S
- Page 1 State of California to cause emissions standards. cancer, birth defects, and/or other reproductive harm. For more information, go to www.P65warnings.ca.gov THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE. © 2023 United States Stove Company, 227 Industrial Park Rd., South Pittsburg, TN 37380 Ph. 800-750-2723...
- Page 2 Your stove is Certified to ASTM E1509-12 (2017) and Certified to CAN/ULC S627:2023. This manual describes the installation and operation of the U.S. Stove, 5501S wood heater. This heater meets the 2020 U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters sold after May 15, 2020.
- Page 3 Declaration of Completion: As the qualified person responsible for the work described above, I confirm that the appliance as associated work has been installed as per manufacturer’s instructions and following any applicable building and installation codes. Signed: ______________________________________ Print Name: __________________________________Date: ______________ Home Owner: RETAIN THIS INFORMATION FOR FUTURE REFERENCE © 2023 United States Stove Company...
- Page 4 2. Unpack the top mount controls and ensure that the wiring harness shown is attached securely. 4. Secure the control panel to the top of the stove with two sheet metal screws. © 2023 United States Stove Company...
- Page 5 CORD IN FOOT TRAFFIC AREAS OR PINCH THE CORD UNDER FURNITURE. US Stove highly recommends your stove be installed by a qualified NFI (US) or WETT (Canada) technician. To find the nearest qualified installer, go to: https://nficertified.org, https://www.wettinc.ca/ © 2023 United States Stove Company...
- Page 6 Side Wall to Stove 7.5” 191 mm Front to Stove 8” 204 mm Side Wall to Vent Pipe 11.25” 286 mm Back to Flue 2” 51 mm Back Wall to Vent Pipe 3” 73 mm © 2023 United States Stove Company...
- Page 7 The maximum recommend vertical venting height is 12- • The heater must be electrically grounded to the steel feet for 3-inch type “PL” vent. Total length of horizontal © 2023 United States Stove Company...
- Page 8 Vent surfaces can get hot enough E. Minimum 2-foot (0.61m) clearance above any grass, to cause burns if touched by children. Noncombustible plants, or other combustible materials. shielding or guards may be required. © 2023 United States Stove Company...
- Page 9 18” (457 mm) above ground level, a an offset is required, it is better to install 45-degree straight section of pellet vent pipe can be used through elbows rather than 90-degree elbows. © 2023 United States Stove Company...
- Page 10 • The levels of heat output will incrementally change on the bar graph starting from heat range “1” to heat range • When room temperature drops below desired set-point “5”. the stove will ramp back up until it reaches the desired temperature. © 2023 United States Stove Company...
- Page 11 5. Waste petroleum products, paints or paint thinners, rate. Any additional fuel introduced by hand will not or asphalt products; increase heat output but may seriously impair the stoves © 2023 United States Stove Company...
- Page 12 Use only the burn pot supplied with this heater. Hopper lid must be closed in order for the unit to feed pellets. During the start-up period: • Make sure the burn pot is free of pellets. © 2023 United States Stove Company...
- Page 13 “E3” thermodisc. This unit has a manual reset thermodisc. This safety switch has two functions. A. To recognize an overheat situation in the stove and shut down the fuel feed or auger system. © 2023 United States Stove Company...
- Page 14 • Heat Exchanger - There is a clean out plate on both sides of the heat exchanger that need to be removed to Clean-Out clean fly ash out of the heat exchanger. The cleanouts are located inside the cabinet doors, on the lower Plate © 2023 United States Stove Company...
- Page 15 Make sure you stove gaskets and chimney joints are in good working order © 2023 United States Stove Company...
- Page 16 DO NOT substitute alternative materials for Glass Wiped Cleaned the glass. Contact your authorized dealer to obtain Hopper (end of Empty & this glass. season) Vacuumed © 2023 United States Stove Company...
- Page 17 If this appliance is installed in a transportable building, removal of the chimney/venting is required for transportation of the building. DO NOT INSTALL IN AN ALCOVE DO NOT INSTALL IN ANY FIREPLACE © 2023 United States Stove Company...
- Page 18 If the other items check out OK, replace the high limit switch. ATTENTION: This wood heater needs periodic inspection and repair for proper operation. It is against federal regulations to operate this wood heater in a manner inconsistent with operating instructions in this manual. © 2023 United States Stove Company...
- Page 19 (you may want to remove the hose entirely off the stove and the air switch first and make sure it is clear). If you hear a click, the air switch is working. BE CAREFUL TOO MUCH VACUUM CAN DAMAGE THE AIR SWITCH. © 2023 United States Stove Company...
- Page 20 The control board is not sending power to the POF There should be a 5-volt (approximately) current going to the thermodisc or other auger system components. POF thermodisc after the stove has been on for 10 minutes. © 2023 United States Stove Company...
- Page 21 Remove the auger motor from the auger shaft and try to run the The auger motor has failed. unit. If the motor will turn the shaft is jammed on something. If the motor will not turn, the motor is bad. © 2023 United States Stove Company...
- Page 22 Circuit board malfunction. board is fine. If there is NOT power being sent to the blower when it shuts off during operation, then you have a bad control board. © 2023 United States Stove Company...
- Page 23 Check to see if a surge protector is being used on the stove. If not, recommend one to the consumer. High limit switch is malfunctioning. If the other items check out okay, replace the high limit switch. © 2023 United States Stove Company...
- Page 24 Bad Pellets. (Applies to GLASS “SOOT’S” UP AT You might also want to try a brand that is made from a different A VERY FAST RATE Only) type of wood (softwood vs. hardwood). Different woods have different characteristics when being burned. © 2023 United States Stove Company...
- Page 25 REPAIR PARTS © 2023 United States Stove Company...
- Page 26 Call 1-800-750-2723 Ext 5051 or Email to: parts@usstove.com IN ORDER TO MAINTAIN WARRANTY, COMPONENTS MUST BE REPLACED USING USSC PARTS PURCHASED THROUGH YOUR DEALER OR DIRECTLY FROM USSC. USE OF THIRD PARTY COMPONENTS WILL VOID THE WARRANTY. © 2023 United States Stove Company...
- Page 27 WIRING DIAGRAM 7.5A 250V FUSE 1.25A 250V FUSE Ensure the wires are connected to the bottom two prongs of the hopper switch as shown. CORRECT WRONG © 2023 United States Stove Company...
- Page 28 Engineer Name: ____________________________________ Engineer Name: ____________________________________ License No.: ________________________________________ License No.: ________________________________________ Company: __________________________________________ Company: __________________________________________ Telephone No.: _____________________________________ Telephone No.: _____________________________________ Stove Inspected: Chimney Swept: Stove Inspected: Chimney Swept: Items Replaced: ____________________________________ Items Replaced: ____________________________________ © 2023 United States Stove Company...