Publicité
Device-specific safety instructions
• The product must be standing on an even, hori-
zontal surface with clearance to all sides.
• The product may not be operated outdoors.
• Never put objects through the protective grille into
the product.
• Objects that can be pulled (e. g. curtains, plants),
must not be in the immediate vicinity.
• Never expose the product to water or other liq-
uids.
• The product must not be operated in rooms with
bathtubs, showers or swimming pools or near to
wash basins or water connections.
• Remember that moving parts may also be located
behind ventilation and venting slots.
• Switch off the appliance and unplug from the
mains socket when not in use, before filling,
cleaning or other maintain.
• Do not permit the area around the appliance to
become damp or wet, Be aware that high humidity
levels may encourage the growth of biological
organisms in the environment. If the humidifica-
tion output volume cannot be turned down, use
the appliance intermittently. Do not allow absor-
bent materials, such as carpeting, curtains,
drapes, or tablecloths, to become damp.
• Unplug the appliance during filling and cleaning.
• Never leave water in the reservoir when the appli-
ance is not in use.
• Empty and clean the humidifier before storage,
clean the humidifier before next use.
• Micro-organisms that may be present in the water
or in the environment where the appliances is
used or stored, can grow in the water reservoir
and be blown in the air causing very serious
health risks when the water is not renewed. To
prevent nucleation, remove residual water from
the equipment and water tank every time after
three days of use.
• Empty the tank and refill every third day, before
refilling, clean it with fresh tap water or cleaning
agents if required by the manufacturer. Remove
and scale, deposits, or film that has formed on the
sides of the tank or on interior surfaces. And wipe
all surfaces dry.
• Symbols appearing on your device may not be
removed or covered. Signs on the device that are
no longer legible must be replaced immediately.
Read and observe the instructions for use
before using the product for the first time.
Clean the water tank every three days
The protective insulation creates protection
from contact with electric parts under power
by providing additional insulation around the
necessary operational basic insulation. The
protective insulation corresponds to protec-
tion class II.
Your product at a glance
Note: The actual appearance of your
product may differ from the illustrations.
► Overview – p. 2
1. Front grid
2. Mist vent
3. Blades
4. Flexible hose
5. Function indicators
6. Water tank
7. Base
Assembly
Fan assembly
► P. 3, fig. 1
– Align the two supporting tubes into the holes of
the base, then fix in place from the bottom using
the screws provided.
► P. 3, fig. 3
– Loose the two bolts located at the back of the unit
(do not fully unscrew the two nuts or they will fall
off). Fix the motor unit to the tubes and retighten
the nuts
► P. 4, fig. 5
– Install the rear grid, plastic nut, blades, and blade
spinner to the motor shaft and fix in place.
► P. 4, fig. 6
– Install the front grid and net frame, and secure
using the screw on the net frame. Inset the upper
flexible hose on the motor unit into the mist vent
that is located at the front of the fan grid (ensure
the hose is free of kinks).
Water tank assembly
► P. 4, fig. 9
– Place the misting generator on to the base, ensur-
ing it is appropriately seated in the recess.
– Place the water tank on top of the misting gener-
ator. Fit the cover to the top of the water tank.
– Insert the lower flexible hose on the motor unit
into the water tank cover (ensure the hose is free
of kinks)
How to fill the water tank
► P. 5, fig. 11
– Unplug the appliance before filling and cleaning
the water tank.
– Remover the water tank and turn it upside down.
– Twist the cap anticlockwise to unlock it.
– Fill the tank with cold and clean water, making
sure not to overfill it. Do not add any chemicals,
oils, or other additives. Only use cold or warm
water in the water tank. The water must not be
above 40°C.
– Refit the cap and turn it clockwise to lock it in
place.
– Turn the tank over and place it back on the misting
generator.
Operation
Check before switching on!
DANGER! Caution, risk of injury! The
product may only be put into operation if
no faults are found during the check-up.
Ensure that any defective parts are
replaced before the product is used again.
GB
19
Publicité
