Publicité
Additional Safety Information
Wear safety goggles.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the Off posi-
u
tion when the power supply is interrupted, e.g. when
the battery pack is removed. This prevents uncontrolled
restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Do not open the battery. There is a risk of short-circuit-
u
ing.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting, roughing and brush-
ing metal and stone materials, as well as making holes in
Bosch Power Tools
stone materials using diamond core cutters, without the use
of water.
A separate protective guard for cutting must be used when
cutting with bonded abrasives.
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
The power tool must not be used to grind concrete.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Spindle lock button
(3) On/off switch
(4) Speed preselection thumbwheel
a)
(5) Rechargeable battery
a)
(6) Battery release button
(7) Low-vibration auxiliary handle (insulated gripping
a)
surface)
(8) Standard auxiliary handle (insulated gripping sur-
face)
(9) Extraction guard for grinding
(10) Protective guard for grinding
(11) Protective guard for cutting
(12) Mounting flange with O‑ring (M 14)/mounting flange
without O‑ring (M 10)
a)
(13) Carbide grinding head
a)
(14) Grinding disc
a)
(15) Disc brush (M 14)
a)
(16) Cutting disc
a)
(17) Diamond cutting disc
(18) Quick-clamping nut with bar (M 14)
(19) Clamping nut (M 10)
(20) Two-pin spanner for clamping nut/round nut
(21) Handle (insulated gripping surface)
(22) Grinding spindle
a)
(23) Hand guard
a)
(24) Rubber sanding pad
a)
(25) Sanding sheet
a)
(26) Round nut
a)
(27) Cup brush
a)
(28) Conical brush
a)
(29) Diamond annular cutter
a)
(30) Open-ended spanner
(31) Extraction guard for cutting with cutting guide
a) This accessory is not part of the standard scope of delivery.
English | 9
a)
a)
a)
1 609 92A 9PD | (18.07.2024)
Publicité
