Use As Directed - SLV Elektronik DASAR FLAT LED Mode D'emploi

SLV Elektronik GmbH
ENGLISH
INSTRUCTION MANUAL FOR
RECESSED GROUND FITTING
DASAR FLAT LED
1. NOTES ON SAFETY
Installation, mounting or works on the electrical connection may
only be carried out by an approved electrician.
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no
decoration.
Keep children away from the product.
The fixture may only be operated with a complete and intact
protection glass.
Operate the product only when it functions properly:
In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
If touched or further operated there is danger from electric shock,
burning, or fire.
A malfunction exists when:
visible damages appear.
the product does not work properly (e.g. flickering).
smoke, steam or crackling sounds appear.
smell of burning is recognisable.
an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
2.

USE AS DIRECTED

This product serves exclusively lighting purposes and may:
only be operated using a suitable conventional transformer, output:
12V~50-60Hz.
only be operated when firmly mounted.
not be installed in walking areas or in driveways. The luminaire is not
suited for being walked on.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
3. OPERATION
High currents with low-voltage installations!
Check all electrical connections once in a while for a secure fit.
Replacing the light source: Under regular usage the LED bulb has
an extraordinary long lifetime. If nevertheless damage or failure
occurs, contact your local dealer to exchange the LED bulb.
4. MAINTANANCE AND CARE
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil high salt content in the air
thawing salt cleaning agents
fertilizer especially in flowerbeds
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Disconnect the product from the power supply and let it cool down,
before you clean the product.
If disregarded there may be danger of electric shock or by burning
when cleaning the product.
Cleaning: Clean the product on a regular basis using a slightly
moistened, soft and fluff-free cloth. Please also note additional supplied
notes on maintanance and care.
5. ADDITIONAL IMPORTANT NOTES
Storage: The product must be stored in a dry and clean environment. Do
not strain the product mechanically during storage.
Warranty: In case of a warranty contact your dealer.
Disposal: Notes on the correct disposal in Germany are found on
www.slv.de.
6. INSTALLATION
(only by an approved electrician)
Preparing the low-voltage (12 V) power supply: The transformer should
be used up to 80 % of its capacity. The total watt power of the connected
light fittings must not exceed the power output of the transformer. The
distance between spot and transformer should be at least 20 cm. Note the
manufacturers information for the transformer.
Switch off the mains or respectively the connection lead before doing
any works.
There exists mortal danger from an electric shock.
High currents with low-voltage installations!
Use only heat resistant wires and clamps to avoid danger of fire.
Use only parts, which are supplied with the product or are described as
accessories!
Otherwise the product or the whole installation may not be secure.
Danger for life or danger of fire may exist!
Inspect the product for loose parts inside the housing. When there are
loose parts inside the housing and these are not explicitly described the
product may not be installed or operated.
The housing maybe voltage-carrying. Danger of electric shock!
Unpacking
Consignment:
Plastic casing
Carefully take the product out of the packaging removing any transport
safeguards.
Before disposal of the packaging material make sure that all
components of the product are removed.
Installation place
The product is solely suited for recessed floor installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
Before installation
Do not try to seal the product yourself, using additional silicon or
another sealant.
Carry out the installation when the weather is dry.
Prepare the recess if not done yet. When installing the lighting unit
outdoors provide a gravel bed, 20 cm thick, beneath the installation pot.
This serves as protection from corrosion.
Prepare the power supply lead according to valid rules for outdoor
installations.
Separate Installation Steps
Take the fixture out of the plastic casing.
Fix the plastic casing firmly into the earth.
Electrical Connection
Establish the connection as shown in the schematic drawing 1.
Connect the product with the prepared 12V~50-60Hz power supply.
All connections must be properly protected and sealed against
penetration of water and dirt!
Place the fixture in the installed plastic casing.
Check if the product functions properly and is securely fixed.
The product is now ready for operation.
1
g f d e d
a: Fitting b: Installation pot
c: Connection lead of the fitting d: Shrinking tube
e: Blank tube f: Cast-resin sleeve or watertight
connection unit
g: Power supply lead h: Drainage
art.-no. 228401/02
12/2009 © SLV Elektronik GmbH, Daimlerstr. 21-23, 52531 Übach-
Palenberg, Germany, Tel. +49 (0)2451 4833-0
Technical Details are subject to change.
a
b
c
h
20cm