Publicité
ASSEMBLY STEPS
Please see illustrations at the end of the manual for further assembly instructions.
I
Assembly of spring:
1. Place H1 (5) element between first and second scroll of spring (G). Pay attention for correct positioning of the bracket
(refer to point 5).
2. Place H1 (4) element between second and third scroll of spring. Tilt at an angle H1 (4) element and insert it into H1 (5)
element. Push the whole until it's blocked. Pay attention for correct positioning of the bracket (refer to point 5).
3. Place H2 (7) element between first and second scroll of spring. Pay attention for correct positioning of the bracket (refer
to point 5).
4. Assemble from the bottom of spring elements H1 (6) and H2 (8).
5. Before proceeding to point 6, please check correct positioning of all brackets. Marks on all brackets should be located
inside of the spring toward the closer end of the spring. On corresponding drawing no.5 shown correct bracket's posi-
tioning and examples of its wrong positioning.
6. Assemble spring with anchor (I) by using 4x hardware set (H3). Screw on the nuts with the ratchet spanner.
7. Place H1 (5) element between first and second scroll of spring (G) (looking from the top). Pay attention for correct po-
sitioning of the bracket (refer to point 11).
8. Place H1 (4) element between second and third scroll of spring (looking from the top). Tilt at an angle H1 (4) element
and insert it into H1 (5) element. Push the whole until it's blocked. Pay attention for correct positioning of the brack-
et(refer to point 11).
9. Place H2 (7) element between first and second scroll of spring (looking from the top). Pay attention for correct position-
ing of the bracket (refer to point 11).
10. Assemble from the top of spring elements H1 (6) and H2 (8).
11. Before proceeding to point 12, please check correct positioning of all brackets. Marks on all brackets should be located
inside of the spring toward the closer end of the spring. On corresponding drawing no.11 shown correct bracket's posi-
tioning and examples of its wrong positioning.
12. Assemble spring with suspension frame (D) by using 4x hardware set (H3). Screw on the nuts with the ratchet spanner.
IIa Assembly of spring and flat anchor:
1. Find a suitable location to install the spring animal. See FIG II. After installation the concrete foundation will need to be
covered with a shock absorbing surface. The use of rubber tiles is recommended.
2. Place the flat anchor (I-a) horizontally, using the spirit level, at the desired location and mark the holes.
3. Drill the 4 holes of 90 mm deep.
4. Remove the dust out of the drilled holes.
5. Put the 4 wedge anchors (J) in the holes.
6. Screw on the nuts of the 4 wedge anchors (J) with the ratchet spanner.
IIb Assembly of spring and concrete anchor:
1. Find a suitable location to install the spring animal. Do not dig holes in loose soil or sand. The soil should be stable and
compacted to provide proper support. See FIG II.
2. Dig a hole for the anchor of the metallic spring pedestal (I-b). The hole needs to be 700 mm wide at the bottom and
400 mm deep.
3. Flatten the bottom of the hole and stamp with your feet. Place the metallic spring pedestal (I-b) straight up in the hole.
The best way is to use a spirit level. You can fix this position by putting a heavy stone or brick on the suspension frame
(D) after its earlier protection against scratches.
4. Mix enough concrete to fill the hole. Be careful to follow the manufacturers instructions. Pour concrete into the hole. Be
careful to keep the spring and upper side top plate free of concrete. Make sure the spring is straight using a spirit level.
5. Allow concrete to set overnight before going to step 6.
6. Cover the visible concrete with soil so that the complete ground level is flat again. Make sure the ground is covered in
a suitable way (eg. rubber tiles, bark, wood chips,...).
III Assembly of the spring toy:
Remark: Before assembly, it is recommended to coat the threads with thread grease (F) designed for stainless screws.
Remove the grease excess.
1. Place the base board (C) on the suspension frame (D). Put into the pockets on the base board (C) handgrip (A). Then
put the foot support (B) to the bottom of the support beam (D). The whole assembly by using the hardware set (E).
Remark: The soil under the spring animal requires an adjusted surface that is shock absorbing!
assembly steps
Instructions for use - M177.021 - spring toy in HDPE - 'z - line'
EN
p. 22-25
p. 26
p. 27
p. 28
9
Publicité
