Publicité
GB
Table of contents
Before you begin... . . . . . . . . . . . . . . . . . . . . . . 14
For your safety . . . . . . . . . . . . . . . . . . . . . . . . . 14
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Claims for defects . . . . . . . . . . . . . . . . . . . . . . 39
Before you begin...
Intended use
The product is intended for the location and guidance
of suitable angle grinders (perm. cutting disc diame-
ter: ► Technical data – p. 16).
It may only be used to cut metal workpieces.
This product is not intended for commercial use. Gen-
erally acknowledged accident prevention regulations
and enclosed safety instructions must be observed.
Only perform work described in these instructions for
use. Any other use is improper. The manufacturer will
not assume responsibility for damage resulting from
such use.
What are the meanings of the symbols used?
Danger notices and information are clearly marked
throughout these instructions for use. The following
symbols are used:
DANGER! Direct danger to life and risk of
injury! Directly dangerous situation that
may lead to death or severe injuries.
WARNING! Probable danger to life and
risk of injury! Generally dangerous situa-
tion that may lead to death or severe inju-
ries.
CAUTION! Possible risk of injury! Dan-
gerous situation that may lead to injuries.
NOTICE! Risk of damage to the device!
Situation that may lead to property damage.
Note: Information to help you reach a better
understanding of the processes involved.
These symbols identify the required personal protec-
tion equipment:
For your safety
General safety instructions
• To operate this device safely, the user must have
read and understood these instructions for use
before using the device for the first time.
• Observe all safety instructions! Failure to do so
may cause harm to you and others.
• Retain all instructions for use, and safety instruc-
tions for future reference.
• If you sell or pass the device on, you must also
hand over these operating instructions.
14
• The device must only be used when it functions
Cutting stand
properly. If the product or part of the product is
defective, it must be taken out of operation and
disposed of correctly.
• Keep children away from the device! Keep the
device out of the way of children and other unau-
thorised persons.
• Do not overload the device. Do not use the device
for purposes for which it is not intended.
• Make sure to always wear the required personal
protective equipment.
• Exercise caution and only work when in good con-
dition: If you are tired, ill, if you have ingested
alcohol, medication or illegal drugs, do not use the
device, as you are not in a condition to use it
safely.
• This product is not intended to be used by per-
sons (including children) or who are limited in their
physical, sensory or mental capacities or who lack
experience and/or knowledge of the product
unless they are supervised, or have been
instructed on how to use the product, by a person
responsible for their safety.
• Ensure that children are not able to play with the
device.
• Always comply with all applicable domestic and
international safety, health, and working regula-
tions.
Device-specific safety instructions
• The cutting stand must always be reliably and
firmly screwed to the workbench.
• Only use suitable cutting discs for metal. Never
use circular saw blades or roughing discs
• Check the cutting disc of your angle grinder for
damage on a regular basis. Never use the disc if
you discover dents, notches or any other damage.
• Never work without cutting disc guard and stand-
ardised spark guard.
• Always remove the mains plug:
– before changing products or tools;
– before maintenance work;
– when not in use.
• Read the instructions for use before using the
angle grinder for the first time.
• Before use, make sure that the angle grinder is
secured in the holder in accordance with the
instructions.
• Make sure that the mains cable is kept a safe dis-
tance away from the cutting disc and work area.
• Ensure that the workpiece is properly clamped
between the two clamping jaws and seated
securely on the baseplate.
• Never process workpieces that are too large or
too small.
• Always wear safety goggles, hearing protection,
protective gloves and a dust mask when working
with the angle grinder.
• Wear suitable work clothing and do not wear any
loose-fitting clothing or jewellery that could get
caught up in moving parts. Anti-slip footwear is
recommended. Wear a hair net if you have long
hair.
• Never use your hands or objects to stop the cut-
ting disc.
Publicité
