Publicité
EN
TESTING OF THE UNIT / INFORMATION ON PRODUCT LIABILITY / GUARANTEE DECLARATION
TESTING OF THE UNIT
For safety reasons, we would recommend having the device
checked by an expert as required but at least every 12 months
to ensure that it can continue to operate safely.
In the case of unused devices, the check can be postponed
until they are next started up.
All (potentially deviating) national inspection and mainte-
nance regulations must also be observed.
If you have any questions, please contact your Titan dealer.
IMPORTANT INFORMATION ON PRODUCT LIABILITY
An EU directive valid since 01.01.1990 specifies that the manu-
facturer is only liable for his products if all the parts originate
from the manufactured or are approved by him, and if the
units are mounted and operated properly.
If accessories or spare parts from third parties are used, li-
ability can be partially or completely inapplicable. In extreme
cases the responsible authorities can prohibit the use of the
entire unit (German industrial employer's liability insurance
association and factory inspectorate).
With original Titan accessories and spare parts, compliance
with all safety regulations is guaranteed.
NOTE ON DISPOSAL
In observance of the European Directive 2012/19/EU on waste
electrical and electronic equipment and implementation in
accordance with national law, this product is not to be dis-
posed of together with household waste material but must be
recycled in an environmentally friendly way!
Titan or one of our dealers will take back your used waste elec-
trical or electronic equipment and will dispose of it for you in
an environmentally friendly way. If you have any questions,
please contact your Titan dealer.
EU Declaration of conformity
We declare under sole responsibility that this product
conforms to the following relevant stipulations:
2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU
Applied harmonised norms:
EN 62841-1, EN 50580, EN IEC 55014-1, EN IEC 55014-2,
EN IEC 61000-3-2, EN 61000-3-3, EN 62233
The EU declaration of conformity is enclosed with the
product.
22
3 + 2 YEAR GUARANTEE ON THIS TITAN PRODUCT
(Status 03.03.2022)
TITAN exclusively provides the commercial buyer who has
purchased the product from an authorised specialist dealer
(hereinafter referred to as the „Customer") with a guarantee
for the products listed on the Internet at https://go.titantool-
international.com/warranty in addition to the statutory war-
ranty regulations, unless there is a guarantee exclusion.
The warranty period for TITAN products (devices) is 36 months
and begins with the date of purchase of the initial purchase.
This guarantee period is extended by a further 24 months if
the product is registered within 28 days of purchase on the
Internet at https://go.titantool-international.com/registration.
In cases of commercial rental, industrial use (e.g. use in shift
operation) or equivalent use, the guarantee period is 12
months due to the significantly higher load. We reserve the
right to carry out a check in individual cases and refuse the
guarantee where necessary.
If any material, machining or performance defects are identi-
fied in the device within the guarantee period, then the gua-
rantee claims must be made immediately and within a period
of no more than 2 weeks following discovery of the defect.
The detailed guarantee conditions can be obtained on
request from our authorised TITAN partners (see website or
operating instructions) or in text form on our website:
https://go.titantool-international.com/warranty-conditions
UKCA Declaration of conformity
We declare under sole responsibility that this product
conforms to the following relevant regulations:
Supply of Machinery (Safety) Regulations 2018
Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
The Waste Electrical and Electronic Equipment Regulations
2013
Applied harmonised standards
BS EN 62841-1, BS EN 50580, BS EN IEC 55014-1,
BS EN IEC 55014-2, BS EN 61000-3-2, BS EN 61000-3-3,
BS EN 62233
Capspray X80
Subject to modifications
Publicité
