Publicité
Connecting the Cnits
Note:
This unit is for vehicies with a 12-volt bat-
tery and negative grounding. Before
installing it in a recreational vehicle,
truck, or bus, check the battery voltage.
To avoid shorts in the electrical system,
be sure to disconnect the battery © cable
before beginning installation.
Refer to the owner's manual for details
on connecting the various cords of the
power amp and other units, then make
connections correctly.
Secure the wiring with cable clamps or
adhesive tape. To protect the wiring,
wrap adhesive tape around them where
they lie against metal parts.
Route and secure all wiring so it cannot
touch any moving parts, such as the gear
shift, handbrake, and seat rails. Do not
route wiring in places that get hot, such
as near the heater outlet. If the insulation
of the wiring melts or gets torn, there is a
danger of the wiring short-circuiting to
the vehicle body.
Don't pass the orange lead through a
hole into the engine compartment to con-
nect to the battery. This will damage the
lead insulation and cause a very danger-
ous short.
"
Do not shorten any leads. If you do, the
protection circuit may fail to work when it
should.
Never feed power to other equipment by
cutting the insulation of the power supply
lead of the unit and tapping into the lead.
The current capacity of the lead will be
exceeded, causing over heating.
When replacing fuse, be sure to use only
fuse of the rating prescribed on the fuse
holder.
if the RCA pin jacks on the unit are not
being used, do not remove the caps
attached to the end of the connector.
Since a unique BPTL circuit is employed,
never wire so the speaker leads are
directly grounded or the left and right
speaker © leads are common.
- Speakers connected to this.unit must be
high-power types possessing minimum
rating of 35 W and impedance of 4 to 8
ohms. Connecting speakers with output
and/or impedance vaiues other than
those noted here can damage the speak-
ers.
When an external power amp is being
used with this system, be sure not to con-
nect the blue lead to the amp's power ter-
minal. Likewise, do not connect the blue
lead to the power terminal of the auto-
antenna. Such connection could cause
excessive current drain and malfunction.
To prevent incorrect connection, the input
side of the IP-BUS connector is blue, and
the output side is black. Connect the con-
nectors of the same colors correctly.
¢ If this unit is installed in a vehicle that
does not have an ACC (accessory) posi-
tion on the ignition switch, the red lead of
the unit should be connected to a termi-
nal coupled with ignition switch ON/OFF
operations. If this is not done, the vehicle
battery may be drained when you are
away from the vehicle for several hours.
ACC position
Connection Diagram 1 (Fig. 7}:
When DSP is not connected
Connection Diagram 2 (Fig. 8)
When connected with "DEQ-P800"
Hideaway DSP
Connection Diagram 3 (Fig. 9)
When connected with another DSP than
"DEQ-P800"
Hideaway DSP or equalizer:
. Antenna jack
. Black (ground)
To. vehicle (metal) body.
3. Red
i
To electric terminal controlled by ignition
switch (12 V DC) ON/OFF.
4. Orange
:
To terminal always supplied with power
regardless of ignition switch position.
5. Yellow
To lighting switch terminal.
6. Yellow/biack
Cetlular Mute
Sf you use a cellular telephone, connect it via
the Audio Mute jead on the cellular tele-
phone. If not, keep the Audio Mute lead free
of any connections.
:
. Fuse resistor
. Fuse holder
. IP-BUS input (blue)
Blue
To system control terminal of the power amp
or Auto-antenna relay control terminal
(Max. 300 mA 12 V DC).
ae
11. Blue
12. Front/left speaker
13. Front/right speaker
14. Green
15. Gray
16. Green/black
17. Gray/biack :
18. Green/red**
19. Gray/red
20. Black/green
21. Black/gray
22. With a 2 speaker system, connect to the 2
speakers in the front or the rear.
23. Rear/left speaker
24. Rear/right speaker
25. Subwoofer speaker
No
Soon
=
26. Gray labei (subwoofer output or audio output)
27. Green label (rear output or rear input)
28. White jabei (front output or front input)
29. Multi-CD player, etc. (sold separately)
30. Use this for connections when you have the
separately available amplifier.
31. White
32. Red
33. Connecting cords with RCA pin piugs
(solid separately)
34. Power amp (solid separately)
35. DSP system + Subwoofer system + Multi-CD
player (sold separately)
36. To the Front output terminal
37. To the Rear output terminal
38. To the Input terminal
39. Hideaway DSP unit "DEQ-P800"
(sold separately)
40. Another DSP than "DEQ-=P800" Hideaway DSP
or equalizer (sold separately)
Publicité
