Husqvarna LC 247 Manuel D'utilisation page 15

Note:
Use a funnel to prevent spill.
8. Install the oil tank cap when the oil level is correct.
To replace the engine oil
WARNING:
directly after the engine is stopped. Let the
engine become cool before you drain the
engine oil. If you spill engine oil on your skin,
clean with soap and water.
(Fig. 39)
1. Operate the product until the fuel tank is empty.
2. Remove the ignition cable from the spark plug.
3. Remove the oil tank cap and the attached dipstick.
4. Put a container below the product to collect the
engine oil in.
5. Tilt the product or drain the engine oil from the oil
tank with an oil pump (accessory).
6. Fill with new engine oil of the type recommended in
Technical data on page 18 .
7. Do a check of the oil level. Refer to
the oil level on page 14 .
8. Install the oil tank cap when the oil level is correct.
Battery (LC 347VE, LC 353VE)
WARNING:
decreases the safety of the product. Always
use a battery approved by the manufacturer.
The battery gives power to the electrical start and is a
safety device that prevents accidental start. Remove the
battery when you do not operate the product and when
you let it stay out of view.
To use the battery for the first time
CAUTION:
become empty. If the battery becomes
empty, it can cause damage to the battery.
You must charge the battery before first operation.
1. Connect the battery charger to the battery, refer to
To charge the battery on page 15 .
2. Wait until a minimum of 1 green LED comes on.
3. Attach the battery to the engine, refer to
start (LC 347VE, LC 353VE) on page 12 .
To charge the battery
If only 1 or 0 lamp indicators on the battery are on, it is
necessary to charge it. An empty battery is fully charged
in 2 hours. To charge for shorter periods of time does
not do damage to the battery.
808 - 010 - 06.11.2024
Engine oil is very hot
To do a check of
A damaged battery
Do not let the battery
Electrical
1. Connect the battery charger to the battery. (Fig. 40)
2. Connect the battery charger to a power socket,
100-240V, 50-60Hz.
3. Remove the charger from the power socket first,
then remove the charger from the battery.
Status for battery charge
LED display on the battery
LED 1 flashes red.
LED 1 is constant red.
LED 1 is green and LED 2 is red.
LED 1 and 2 are green and LED 3 is
red.
LED 1, 2 and 3 are green and LED 4
is red.
Lamp indicator on the bat-
tery charger
Constant red light
Constant green light
To do a check of the spark plug
CAUTION:
recommended spark plug type. Incorrect
spark plug type can cause damage to the
product.
• Do a check of the spark plug if the engine is low
on power, is not easy to start or does not operate
correctly at idle speed.
• To decrease the risk of unwanted material on the
spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly
adjusted.
b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.
• If the spark plug is dirty, clean it and make sure that
the electrode gap is correct, refer to
on page 18 . (Fig. 41)
• Replace the spark plug if it is necessary.
Air filter
A dirty air filter can cause the engine to be damaged
or not operate correctly. Do maintenance on the air
filter more frequently in dusty conditions. Refer to
Maintenance schedule on page 13 for information about
when to replace the air filter.
Status
1%-9%
10%-32%
33%-54%
55%-77%
78%-100%
Status
The battery charges.
The battery is fully charg-
ed.
Always use the
Technical data
15