Bosch GBM 1600 RE Professional Notice Originale page 7

Technical data
Drill
Article number
Rated power input
No-load speed
Rated torque
Spindle collar diameter
Max. drilling diameter
– Steel
– Wood
– Aluminium
Chucking capacity
Right/left rotation
Maximum stirrer paddle dia-
meter
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Fitting
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Auxiliary handle (see figure A)
Only use your power tool with the auxiliary handles
u
(2) and (4).
Screw the auxiliary handle (2) into the thread (3) on the mo-
tor housing.
The auxiliary handle (4) can be continuously rotated through
360°.
Changing the tool (see figure B)
Wear protective gloves when changing tools. The drill
u
chuck may heat up significantly when it is used for long
periods.
Keyed chuck with automatic lock
Open the keyed chuck (1) by turning it until the tool can be
inserted.
Insert the tool. Insert the drill chuck key (9) into the corres-
ponding holes of the keyed chuck (1) and clamp the tool
evenly.
Changing the drill chuck (see figure C)
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Removing the securing screw
A securing screw (10) protects the keyed chuck (1) from be-
ing accidentally separated from the drill spindle.
Bosch Power Tools
Open the keyed chuck (1) fully and unscrew the securing
screw (10) clockwise. Note that the securing screw has a
GBM 1600 RE
left-hand thread.
3 601 AB0 0.. When the securing screw (10) is securely seated, place a
screwdriver on the screw head and undo the securing screw
W 850
by hitting the handle of the screwdriver.
-1
min 630
Removing the drill chuck
Nm 11
To remove the drill chuck (1), place an open-ended spanner
mm 43
(SW 17) onto the nut on the drive spindle.
Hold the keyed chuck firmly in one hand and use your other
hand to turn the open-ended spanner anticlockwise until the
mm 16
drill chuck comes away from the drill spindle cone.
mm 40
Installing the drill chuck
mm 16
u
mm 3–16
●
To install the keyed chuck (1), turn the nut on the drive
mm 160
spindle clockwise as far as it will go.
Push the keyed chuck onto the drive spindle until it is se-
kg 3.0
curely seated, but do not use force when doing so.
Use a rubber hammer to lightly hit the front side of the keyed
/ II chuck (1) in order to ensure that the keyed chuck is securely
seated. When doing so, ensure that the clamping jaws of the
keyed chuck do not protrude to avoid damaging the chuck.
Installing the securing screw
Screw the securing screw (10) anticlockwise into the open
keyed chuck. Always use a new securing screw because a se-
curing adhesive substance is applied on its thread and is
rendered ineffective after repeated use.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
u
Operation
Starting Operation
u
Keep the cone of the drill spindle and the hole of the
drill chuck free of grease and dirt.
Avoid dust accumulation at the workplace. Dust can
easily ignite.
Pay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
1 609 92A 4GU | (29.08.2018)
English | 7