Publicité
EN
Note:
• Rinse the filter grid with clean water and do not add
any detergent.
• Do not clean the filter grid with a brush or fingers.
• Allow the filter grid to air dry for at least 24 hours.
Wiping module (clean after each use)
1. Remove and clean the cloth.
2. Wipe the water tank dry.
Sensors (clean regularly)
Clean the sensors with a soft cloth as follows:
1. Clean the rechargeable sensor on the left side, the two
laser sensors on the front and one on the side of the
robot and all the sensors shown in the picture.
2. Wipe also the charging contacts on the bottom of the
robot, unplug the charging contacts on the docking
station before cleaning.
3. Similarly, wipe the signal transmission point of the
docking station.
Anti-fall sensor
Recharging
contact
Ultrasonic
sensor
Infrared sensor
82
Sensors (clean every month)
LDS laser range-
finder
Anti-collision sensor
for radar sensor
Anti-collision
sensor
Infra-red
charging sensor
Battery
• The appliance is equipped with high-performance
lithium-ion
batteries.
To
maintain
battery
performance, keep the appliance charged every day.
• If the appliance is not used for a long time, turn it off
and store it properly. Charge it at least every 3 months
to prevent damage to the batteries due to excessive
discharge.
Firmware update
Use the mobile app to update the firmware. If new
firmware is detected, update as prompted. When
updating the firmware, the battery level should be ≥50 %
and the appliance must be placed in the docking station.
Docking station
• Regularly check the bag in the docking station. If the
bag is full, replace it with a new one.
• Clean the charging contacts and the suction opening.
• Remove the coarse filter of the docking station
and rinse it with water. Allow it to dry properly and
reinstall it.
COMMON PROBLEMS
Problem
The robot cannot be
• If the battery is low, place the robot in the docking station and align it with the
started
board contacts, the appliance will start automatically (if the robot is completely off,
it can start automatically after a while).
• Do not use the appliance if the ambient temperature is below 0 °C or above 50 °C.
Use at 0-40 °C.
The robot cannot be
• Move the robot off the station, make sure the docking station indicator light turns
charged
on, and make sure both ends of the docking station power adapter are properly
connected.
• In case of poor contact, clean the docking station contact points and charging
contacts on the robot or turn the side brush to the side.
The robot cannot be
The robot is too far from the docking station, place it near the docking station and try
recharged
again.
Abnormal behaviour
Turn off the robot and restart it.
Unusual noise is heard
The main brush, side brush or wheel may be wrapped with foreign objects, turn off the
during use
robot and remove foreign objects.
Cleaning ability is
• The dust container is full. Clean it.
reduced or dust is
• The filter grid is clogged. Clean or replace.
• The main brush is wrapped with foreign objects, clean it.
dropping from the
appliance
Wi-Fi cannot be
• The Wi-Fi signal is bad. Check that the correct Wi-Fi coverage is available.
connected
• Wi-Fi is connected in an unusual way. Reset Wi-Fi, download the latest app, and try
connecting again.
• The password is entered incorrectly.
• There is a router for the 5GHz frequency band, the robotic vacuum cleaner is
equipped only for the 2.4GHz frequency band.
The planned cleaning did
If the battery level is low, planned cleaning can only be started if the battery level is
not take place
at least 30 %.
Does the robot consume
The robot consumes a small amount of power when it is permanently placed in the
power when it is always
docking station, allowing the best battery performance.
placed in the docking
station?
Do I need to charge the
The lithium battery can be used immediately after charging and has no memory effect.
robot three times for 16
hours the first time?
EN
Remedy
83
Publicité
