Publicité
EN
KEY FEATURES
Cleaning / ON/OFF
• Press briefly to start or pause cleaning.
• Press and hold for 3 seconds to switch the appliance
on or off.
• Long press for 15 seconds to force the appliance to
shut down under unusual circumstances.
Charging / Local cleaning
• Press briefly to start or pause charging.
• Long press to start local cleaning.
Indicator light
• Orange: Normal operation or charging.
• Red: Abnormal condition or low battery.
• Red-orange: The appliance is not connected to the
network.
Wi-Fi reset
• Press both buttons simultaneously for 3 seconds.
INSTALLATION
1. Connect the power cord and store the excess
cable length in the cable compartment.
2. Place the docking station against the wall and
connect the power.
Note:
• Provide a space of min. 0.5 m on both sides of the
docking station and min. 1.5 m in front of the station.
• If the power cord is stretched vertically to the ground,
the appliance may pull it out and the docking station
may be switched off.
• In normal condition, the charging indicator light is on
when switched on. When the appliance is charged, the
indicator remains lit.
3. Do not move the docking station or expose it to
direct sunlight.
Note: Direct sunlight will interfere with the docking
station signal and the appliance may not return to the
docking station properly.
4. Installing the side brush
Make sure the left side brush (L) and right side brush
(R) markings correspond to the L and R markings on
the bottom cover. Push the side brushes L and R until
you hear a "click" sound.
5. Putting the appliance into operation and charging
To switch the robot on, press and hold the button
If the power indicator light is normally on, charge the
robot in the docking station.
Note: If the appliance does not start due to a low
battery, charge it in the docking station and it will start
automatically. Normally, the appliance can only operate
when the battery level is ≥15 %.
78
6. Connecting a mobile app (you can skip this step)
Read the instructions for connecting Wi-Fi and connect
the mobile app.
7. Start of cleaning
After switching on the robot, briefly press the button
on the robot or start cleaning using the mobile app
(you can pause the appliance by pressing any button
during use).
Note:
• The sweeping robot cannot be used to remove fluids.
• If the battery charge level is less than 15 %, the
appliance cannot operate. In this case, recharge it.
• If the battery charge level is less than 15 %, the
appliance automatically returns to the docking station.
• Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
appliance catches these wires.
• Do not carry the robot during operation. Always use
the manual control designed for controlling the robot.
8. Installing the wiping module
a) Installing the wiping cloth: glue the wiping cloth
straight to the bottom of the water tank.
Note: Clean the wiping cloth after use to keep it in good
condition.
b) Fill the water tank: open the cover and fill the tank
with water.
.
c) Install the module:
Push the module horizontally along the back of the
robot. The module is installed in place when you
hear a "click" sound.
9. Removing the wiping module
Once the robot has completed its work, press the
latches on both sides, remove the wiping module
backwards, empty the water from the water tank and
clean the cloth (do not move or flip the robot during
cleaning).
10. Instructions for using the wiping module
• Do not use the wiping module unless supervised.
• For safety, make sure the wiping module is removed
when charging or when not in use.
• Do not attempt to wipe the carpet.
• For a better wiping effect, the wiping module should
be used after sweeping or vacuuming the floor three
times. Only distilled, demineralised or filter kettle
water can be used in the water container.
• To refill water or clean the cloth while the appliance
is operating, pause it, remove and reinsert the wiping
module as described in steps 8 and 9. Do not move or
flip the appliance to avoid positioning errors and map
loss.
• We recommend soaking the wiping cloth before
mopping for better cleaning.
• The wiping function of the appliance is designed for
wiping and aids deep cleaning. However, it cannot
effectively remove stubborn dirt and thus replace
human power.
USE
ON/OFF
Press and hold the button
for 3 seconds, the indicator
light comes on and the appliance starts.
Press and hold the button
for 3 seconds while the
appliance is in standby mode, the indicator light flashes
red and the appliance switches off.
NOTE: The appliance cannot be switched off while it is
being charged.
CLEANING/PAUSE
After starting the appliance, briefly press the button
the appliance or start the appliance using the mobile app
(press any button to pause the appliance).
Note:
• The robotic vacuum cleaner cannot be used to remove
fluids.
• If the battery charge level is less than 15 %, the
appliance cannot operate. In this case, recharge it.
• If the battery charge level is less than 15 %, the
appliance automatically returns to the docking station.
• Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
robot catches these wires.
CHARGING
Automatic mode: The appliance automatically returns to
the docking station after work. The dirt is sucked out of
the container. Then the robot heads back to the docking
station to charge.
Manual mode: When paused, press the button
to start charging or you can use your mobile app to
charge the appliance. The indicator light flashes when the
appliance is fully charged.
Note: If the appliance does not find the docking station,
it will automatically return to its original position. In this
case, place the device manually into the docking station.
COMPLETE AUTOMATIC CLEANING
Once the robot is on, it performs a search, generates
a map and intelligently divides it into areas. Then it sweeps
the areas one after the other properly, efficiently and
thoroughly along the wall and plans a curved / S-shaped
cleaning path. After cleaning, the robot automatically
returns to the charging base.
Note: Do not move the robot arbitrarily and often during
cleaning. After moving, place the robot in its original
position. When the robot is on again, it will try to take
a position itself. After successful positioning, the robot
will follow the planned path and continue working. If
positioning fails, the robot cancels the previous task,
creates a map, and cleans up again. Even if it does not find
a charging base.
LOCAL TURBO CLEANING
If a local area needs more thorough cleaning, the user
specifies an area of 1.5 x 1.5 m that he/she wants to clean
on the map. The appliance automatically moves to this
area and starts cleaning it. The appliance cleans the area
twice using the TURBO suction power.
LOCAL CLEANING
If you cannot control the robot using the mobile app,
move the robot manually to the place you want to clean
up. Press the button
for 3 seconds and the robot will
on
perform double cleaning in the area of 1.8 x 1.8 m with
the centre in its starting position.
ZONE CLEANING
Use the mobile app to set the size and location of the area
you want to clean up. You can set up to 15 areas. The robot
will clean in the areas you have set.
EN
briefly
79
Publicité
