Publicité
Programs
SECTION
1
2
P01
SPEED 1.0
2.0
P02
SPEED 2.0
2.0
P03
SPEED 1.0
2.0
P04
SPEED 1.0
2.0
P05
SPEED 2.0
2.0
P06
SPEED 1.0
2.0
MAINTENANCE
General
•
Make sure that you have switched off the device and disconnected the power plug before maintenance.
•
Do not use abrasives or solvents to clean the tape, as this may damage the finish and functionality.
•
Take care that excessive moisture does not enter the display panel as this may damage it.
•
Keep the equipment, especially the display console, out of direct sunlight.
•
To clean around the plug and control panel use a soft dry cloth, never use a wet cloth.
•
Do not use the treadmill in a wet or dusty environment as this may cause leakage or mechanical failure.
•
Use this product on a flat surface.
Daily maintenance
Clean regularly to remove dust and sweat to protect the components. You should clean both sides of the exposed
part of the belt to avoid residue. Use a damp cloth with soap to clean the ribbon. Do not use a cleaner. Wipe the
sweat off the handrail and the strap after use.
Lubricant use
The platform and treadmill have been lubricated at the factory with an anti-
static lubricant, but we can re-lubricate it. Suggestion:
-
Use of - 3 hours per week-----lubricate every 6 months.
-
Use 4-7 hours per week-----lubricate every 3 months.
-
Use of + 8 hours per week-----lubricate once a month.
Belt deflection adjustment
To improve the use of the belt, you can adjust it if you notice a deviation of the direction after continuous use. To do
this, adjust the bolts at the front of the base with the Allen key provided as shown in the picture below.
WARNING! The belt should not be too tight as this can cause noise and possible damage to the engine.
Adjustment of the transmission belt
If the drive belt becomes loose, use the spanner clockwise to turn the bolt until the belt no longer slips.. WARNING!
Frequently clean any objects or dust that may fall into the strap.
Correct arrangement of the ignition device
Do not touch the power plug or disconnect it with wet hands. When pulling on the plug, hold the plug by the plastic part,
not directly on the cord. Do not place excessive weight on the cord. Do not wrap the cord around the machine to avoid
damaging it. If the plug, cable or connection is loose, do not use the appliance.
3
4
5
6
7
3.0
4.0
4.0
4.0
3.0
3.0
3.0
4.0
4.0
5.0
3.0
4.0
5.0
4.0
3.0
3.0
2.0
3.0
4.0
3.0
3.0
4.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
3.0
In case of left-
hand deviation,
tighten the
left-hand screw
clockwise or the
right-hand screw
anticlockwise.
8
9
10
11
12
2.0
1.0
2.0
3.0
4.0
5.0
4.0
4.0
3.0
3.0
2.0
3.0
4.0
5.0
4.0
4.0
5.0
5.0
4.0
3.0
3.0
4.0
5.0
4.0
3.0
4.0
3.0
4.0
4.0
5.0
17
13
14
15
16
17
4.0
4.0
3.0
2.0
1.0
2.0
2.0
3.0
3.0
4.0
3.0
2.0
3.0
4.0
5.0
4.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
4.0
5.0
4.0
3.0
3.0
4.0
5.0
In case of right-
hand deviation,
tighten the
right-hand screw
clockwise or the
left-hand screw
counterclockwise.
EN - MC-70
18
19
20
2.0
3.0
2.0
4.0
3.0
3.0
4.0
3.0
2.0
1.0
2.0
3.0
4.0
3.0
2.0
5.0
4.0
3.0
Publicité
