Publicité
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Operation
Suitable blind rivet/nosepiece combinations
The use of a combination not listed in the table below may
lead to poor fastening or a malfunction of the power tool.
Blind rivet
Size
Rivet mandrel
Dia. 3.0 mm (1/8")
Dia. 2.00−2.15 mm
Dia. 3.2 mm (1/8")
Dia. 1.85−2.15 mm
Dia. 4.0 mm (5/32")
Dia. 2.35−2.80 mm
Dia. 4.8 mm (3/16")
Dia. 2.77−3.50 mm
Dia. 5.0 mm (3/16")
Dia. 2.95−3.50 mm
Dia. 6.0 mm (1/4")
Dia. 3.40−3.50 mm
Dia. 6.4 mm (1/4")
Dia. 3.71−4.00 mm
Setting a blind rivet (see figures A1–A3)
– Prepare the workpieces to be connected. If no holes are
yet available, pre-drill the workpieces.
– Select a suitable nosepiece (1). Screw the nosepiece
onto the cover sleeve (2) and tighten it with the
wrench (9).
– Use the AUTO (18) button to select the required working
mode (see "Selecting the working mode", page 20).
– Insert the rivet mandrel of the blind rivet (20) into the
nosepiece (1).
– Hold the power tool tightly and push the blind rivet into
the pilot hole.
– Depending on the working mode, press the on/off
switch (12) and wait until the rivet mandrel has broken
off.
– Tilt the power tool backwards so that the rivet mandrel
can fall into the mandrel container (5).
Note: After setting the blind rivet, ensure that the broken-off
rivet mandrel has fallen into the mandrel container before
setting the next blind rivet.
Bosch Power Tools
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
Capacity
50 °C. Do not leave the battery in your car in the summer, for
80–100 %
example.
60–80 %
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
40–60 %
A significantly reduced operating time after charging indic-
20–40 %
ates that the battery has deteriorated and must be replaced.
5–20 %
Follow the instructions on correct disposal.
0–5 %
Nosepiece
Labelling
3.0/3.2
4.0
4.8/5.0
6.4
Changing the Nosepiece (see figure B)
The nosepiece magazine (4) contains nosepieces of three
different sizes, enabling the user to exchange nosepieces
quickly.
– Use the wrench (9) to unscrew the nosepiece (1) from
the cover sleeve (2).
– Screw the new nosepiece on and tighten it with the
wrench (9).
Empty the mandrel container (see figure C)
Always empty the mandrel container (5) for broken-off rivet
mandrels before it is completely full in order to prevent
blockages.
– Unscrew the mandrel container (5) by turning it anti-
clockwise.
– Empty the mandrel container (5) into a suitable recycling
or waste bin.
– Screw the mandrel container (5) back onto the power
tool by turning it clockwise.
English | 19
Hole diameter
Dia. 2.3−2.4 mm
Dia. 2.7−2.8 mm
Dia. 3.3−3.4 mm
Dia. 4.6−4.7 mm
1 609 92A 7R1 | (22.06.2022)
Publicité
