Publicité
Liens rapides
*****IT IS ESSENTIAL THAT THESE INSTRUCTIONS ARE HANDED TO USER AFTER FITTING*****
MATERIALS
A
1
Towbar Mainframe
C
1
Centre Tube European facing to 94/20/EC A50-1
D
2
M10 x 30 mm x 1.5 mm Bolts, Nuts, Lock Washers and Flat Washers (20mm O.D.)
D1
1
Side Arm
E
1
M10 x 30 mm x 1.5 mm Bolt, Lock Washer and Flat Washer (20mm O.D.)
E1
1
Cleat
F1
4
Spreader plates with captive M10 x 30mm Bolts, Nuts, Lock Washers and Flat Washers (20mm O.D.)
G
2
M12 x 80 mm x 1.75 mm Bolts and Disc Spring Washers
G1
1
Captive Nuts
EP
1
Electrical Plate
CB
2
M16 x 50mm Coupling Bolts, Nuts and Lock Washers
FITTING
1.
Lower and remove spare wheel.
2.
Insert Spreader Plates (F1) inside rear cross member between bumper and rear panel and loosely attach Towbar
Mainframe (A) to vehicle using Nuts and Washers provided.
3.
Lift up floor covering inside boot and remove caps covering hole above frame (this can be achieved by using a screwdriver
through the holes in the frame from below). Insert remaining Spreader Plates (F1) inside frame above and loosely attach
to holes in side arms of Towbar Mainframe (A) using Nuts and Washers provided.
4.
Loosely attach Side Arm (D1) to Towbar Mainframe (A) using Bolts (D) and Flat Washers. Locate the forward mounting in
vehicle chassis and enlarge the square aperture to allow Cleat (E1) to be inserted and loosely secure sidearm using Bolt
(E) and Flat Washer.
5.
Loosely attach Centre Tube (C) to Cross Bar (A) using Bolts (G) with Electrical Plate (EP) and Disc Spring Washers.
Tighten all bolts and refit spare wheel.
Note: Remove Towball/Neck using wheelbrace when not in use to avoid number plate obscuration. (Peugeot only)
Note: This towbar must be used with either a Witter Towball (part number Z1) or Class A50-1 or A50-X towball dimensionally
Conforming to A50-1 with a 'D' and 'S' value greater than or equal to that of the towbar.
Please refer to the vehicle specification for the trailer weight and nose limits, which must be observed.
Recommended torque settings: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm , M14 - 150 Nm, M16 - 214 Nm
WITTER TOWBARS
Deeside Ind. Park, Deeside, CH5 2NY Tel: 01244 284500 Fax: 01244 284577
Fitting
Instructions
For CITROEN SAXO & PEUGEOT 106
C24B
TOWBAR
1996-
Issue 1
Publicité
Manuels Connexes pour Witter C24B
Sommaire des Matières pour Witter C24B
- Page 1 Note: Remove Towball/Neck using wheelbrace when not in use to avoid number plate obscuration. (Peugeot only) Note: This towbar must be used with either a Witter Towball (part number Z1) or Class A50-1 or A50-X towball dimensionally Conforming to A50-1 with a ‘D’ and 'S' value greater than or equal to that of the towbar.
- Page 2 éviter de cacher la plaque d’immatriculation. (Peugeot uniquement) Remarque : Cet attelage doit être utilisé avec une boule de remorquage Witter (référence produit Z11) ou une boule de remorquage Classe A50-1 ou A50-X se conformant dimensionnellement à A50-1 avec une valeur ‘D’ et 'S' supérieure ou égale à...