Publicité
08.5 Cleaning the exterior surfaces
1
Spray an all-purpose cleaner or disinfectant spray on the outside surfaces of the toilet,
including the pan, cistern, and surrounding areas
2
Wipe down these surfaces with a microfiber cloth or paper towel
3
Pay attention to crevices and hard-to-reach areas
4
For stubborn stains or grime, use a scrub brush or toothbrush dipped in cleaner to scrub
the affected areas
5
Rinse the surfaces with water if necessary and wipe them dry
08.6 Cleaning the floor around the toilet
1
Use a mop or cloth to clean the floor around the toilet, removing any dirt or spills
2
Pay attention to the area around the base of the pan
08.7 Maintenance
Removing Lime Scale or Soap Residue/Buildup: Over time, lime scale or soap
n
residue may build up in your toilet assembly These can be removed with commercial-
grade lime or vinegar cleaners Be sure to follow the instructions on the product label
Professional Maintenance: Any other maintenance for this product, especially those
n
involving dismantling parts, should be performed by a competent adult or, preferably, a
professional plumber to ensure safety and proper handling
Regular Inspections: Regularly inspect the toilet assembly for any signs of leaks or
n
damage Early detection can prevent further complications and costly repairs
Seal Check: Periodically check the seal between the toilet base and the floor to ensure it
n
is still intact If the seal appears to be eroding, it may need to be replaced
Toilet Seat Maintenance: Check the toilet seat and its fittings regularly Tighten any
n
loose screws and replace any worn or damaged parts
09 TROUBLESHOOTING
Read and follow assembly instruction If the product does not functioning properly check
troubleshooting table If the product is still not working properly, contact the customer
service department for assistance When calling for assistance, please provide your product
model and serial number
09.1 Fill valve
Symptom
Possible cause
The water level
The position of the
n
in the cistern is
float (33) is not
too high or too
optimal
low.
The fill valve
The water supply
n
does not shut
valve is off
off.
The cistern is
n
obstructing the
movement of the
float (33)
The filter screen is
n
dirty
The fill valve
The cistern is
n
does not
obstructing the
engage.
movement of the
float (33)
The flush valve is
n
leaking
The water level is
n
above the overflow
pipe (52) of the flush
valve
28
Solution
Use the water level adjustment
n
rod (38) to set the float (33) to the
preferred position
Ensure the water supply valve is
n
turned on
Adjust the fill valve to the correct
n
position, ensuring the float (33)
can move freely
Thoroughly clean the filter screen
n
to remove any blockages
Adjust the fill valve to the correct
n
position, ensuring the float (33)
can move freely
Identify the source of the leak
n
If necessary, disassemble the
affected area and firmly seal all
gaps Reassemble everything in
reverse order
Modify the water level so that it
n
sits below the overflow pipe (52)
of the flush valve
| EN |
09.2 Flush valve
Symptom
Possible cause
The flush is
Debris in the cistern
n
weak.
and flush valve is
hindering their
operation and
requires cleaning
The doughnut
Misalignment or
n
washer (48)
improper positioning
does not fit.
There is leaking
The connections are
n
between the
not watertight
seals.
10 DISPOSAL
10.1 Packaging
Children must not play with plastic bags and packaging material, due to the risk of
injury and suffocation Store such material safely or dispose of it in an
environmentally friendly way
Solution
Thoroughly clean and remove
n
any debris from the cistern and
the flush valve After cleaning,
reattach the flush valve body to
the base bracket (47)
Adjust the washer so that its flat
n
end is seated flush with the base
of the cistern
Identify the source of the leak
n
If necessary, disassemble the
affected area and ensure all gaps
are firmly sealed Reassemble
everything in reverse order
Publicité
