Publicité
2. Perform maintenance only as described in this
manual.
3. Any other maintenance can only be carried out by
a specialist service.
4. Do not modify the chainsaw in any way as this
could endanger your safety.
5. Never use tools with damaged switches.
6. If a fault occurs on the machine even though we
carefully carry out regular maintenance and inspec-
tion, have it repaired by a specialist service.
7. In case of any questions and orders for spare
parts, contact the service center.
Chains
! Working with a blunt chain causes rapid wear of the
chain, bar and drive sprocket and can even lead to
chain breakage.
! It is recommended to have the chain sharpened in a
specialized service.
The relevant angles on the teeth of the chain are:
Supplementary angle on the side 85°, Engaging angle
on the upper side 60°, Upper side 30°.
A circular file with a diameter of 4 mm should be used
for grinding the chain.
Guide rail
The lower edge of the bar is exposed to a relatively
large load, therefore, after each grinding of the chain,
it should be turned from the bottom up, and at the
same time, the groove of the bar and the lubrication
holes should be cleaned.
Chain drive wheel
If the teeth on the sprocket (12) show any signs of
wear, the sprocket should be replaced.
The chain wheel should be changed every second
chain change.
Storage when not in use for a long time
Do not store the tool in a place where the temperature
is high.
If possible, store tools in a place with constant tem-
perature and humidity.
TECHNICAL SPECIFICATIONS
Working voltage 20V DC
Use a suitable battery AE2B2020, 20V, 2Ah
or AE2B2040, 20V, 4Ah
and a suitable charger AE2N20123.
Idle speed 3200 min-1
; Cutting bar length 4INCH-101mm
Maximum cutting diameter 80mm
Chain speed at zero load 4 m/s
Chain stop time < 1s
Weight 1,25 kg
Chain thickness 1,1mm
Number of chain links 30
Protection class II.
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 77,9 dB (A) KpA=3
LWA (sound power) 88,9 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Wear hearing protection whenever the sound
pressure exceeds the level of 80 dB (A).
Weighted effective acceleration according to EN
60745:
3,425 m/s2 K=1.5
Caution: The vibration level may vary during
power tool operation from the declared value
depending on the way the power tool is used and
depending on the following conditions: Method of
power tool use and type of material being cut or
drilled, conditions of the power tool and method
of its maintenance, appropriateness of the used
accessories and ensuring its sharpness and good
conditions, the strength of handle gripping, use of
anti-vibration equipment, suitability of the power
tool for the purpose for which it has been designed
and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner,
a hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in
all operating modes, e.g. the time when the power
tool is switched off except for the operation time,
and when it idles, i.e. performs no work. This may
substantially decrease the exposition level during the
whole operating cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith
theseinstructions and provide for its proper
lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENVIRONMENTAL PROTECTIONWASTE
MANAGEMENT
Power tools, accessories and packaging should
be provided for recycling and not to harm the
environment.
Do not dispose of power tools into household waste!
According to Directive 2012/19/EU of the European
Parliament and of the Council on waste electrical and
60
Publicité
