Publicité
to a greater extent by calm work and anticipation as
follows:
Always watch the front of the guide bar when cutting.
Never attempt to cut with the front of the slats.
Be careful when cutting thin and flexible branches.
The saw chain can easily bite into them.
Pay special attention to inserting the bar into already
cut wood when completing the cut.
back pressure (resistance)
Back pressure (resistance) occurs when trying to cut
wood from below, if the chain on the top of the guide
bar touches a solid object, or if the saw chain gets
stuck
Forward thrust
If we do not direct the stop of the scrap against the
cut wood, the chain will pull the saw forward when it
bites or hits a solid object of the wood
If possible, it is therefore important to direct the chip
stop (17) against the wood being cut.
Safety instructions for battery and charger.
Read the operating instructions carefully
before using the battery and charger for
the first time.
! 1. Verify that the electric current that is in the el.
network, is identical to the values indicated on the
battery charger.
! 2. Do not allow moisture, rain or splashing water to
reach the battery charging location.
! 3. Do not charge the battery when the temperature
is below 10 ° C or above 40 ° C. Charging the battery
in extreme temperatures may shorten its life.
! 4. A damaged battery that can no longer be charged
must be treated as hazardous waste. Do not dispose
of the battery in normal household waste, fire or
water.
! 5. Use only batteries and chargers approved by the
manufacturer for use with married equipment.
! 6. Keep the charger clean, free of dust and dirt.
! 7. Always remove the battery before repairing tools.
! 8. Cover the battery contacts to prevent a short
circuit.
! 9. Avoid the risk of explosion!
! 10. Do not smoke while the battery is being charged
or stored. Damaged batteries can leak explosive
gas - hydrogen, which can ignite from open flames
or sparks.
! 11. In case of fire, try to extinguish the fire with earth
or sand.
! 12. The battery and charger become slightly hot
during charging.
! Chemical hazard.
Do not open the battery pack. Protect the battery
from impact. If the accumulator electrolyte leaks,
skin contact must be avoided. If electrolyte contact
with the skin still occurs, rinse the affected area
immediately with water. If electrolyte gets into your
eyes, see a doctor immediately.
- Use protective equipment against noise, dust and
vibration !!!
SAVE THESE SAFETY INSTRUCTIONS !!!
DESCRIPTION
1. Cover
2. Tension screw
3. Switch
4. Handle
5. Battery
6. Chain
7. Security fuse
8. Chain guide bar
Battery and charger are not part of the
delivery
PICTOGRAMS
Pictograms listed on the product packaging:
a) Power values
b) Battery
c) RPM at zero load
d) Chain speed
USE AND OPERATION
ASIST tools are intended for home or hobby use only.
The manufacturer and importer do not recommend
using this tool in extreme conditions and under high
loads.
Any additional requirements must be the subject of
an agreement between the manufacturer and the
customer.
Charging (BA)
Battery and charger are not part of the
delivery.
Warning:
The battery must be charged before using the device
for the first time.
1. Put the battery into the high-speed charger.
2. Insert the plug of the charger into a standard
electrical socket (230V).
3. Connect the charger to the battery charging socket.
4. Normal charging time is approximately 1 hour
(AE2B2020) or 2 hours (AE2B2040). The battery and
charger heat up during charging. It does not indicate
a malfunction of the device.
Warning:
Do not charge the battery for more than 2 hours
(AE2B2020) or 3 hours (AE2B2040). Overcharging
can shorten battery life.
5. After the battery is fully charged, turn off the
charger by disconnecting the AC adapter from the
mains.
6. If the battery is not in use, store it away from heat
sources.
57
Publicité
