Télécharger Imprimer la page

Asist AE4H180-318 Mode D'emploi page 52

Raboteuse d'épaisseur

Publicité

head slots should be cleaned with a brush to remove
stuck-on foreign objects.
Remove resin and other build-up from the feed rollers
and table with a non-flammable solvent.
Lubrication
The recommended lubrication of roller chains is
simply wiping the chain clean. If there is excess dust
or shavings, etc., coat the chain with a thin film of oil,
but never pour oil directly onto the chain. Over-oiling
leads to the accumulation of dust and shavings, which
get between the individual links of the chain and lead
to increased wear and premature replacement of
the chain. This also applies to the speed reduction
and height adjustment chains, as well as the lifting
screws.
The blade head bearings are factory lubricated and
sealed. They do not need any additional care.
Checking and replacing carbons
Carbons must be checked regularly.
If worn, replace both carbons at the same time.
After attaching the new carbons, let the grinder run for
approx. 5 minutes without load.
! Use only carbons of the correct type.
Storage when not in use for a longer period of time
- Do not store the tool in a place where the tempera-
ture is high.
- If possible, store tools in a place with constant
temperature and humidity.
PROBLEM
POSSIBLE CAUSE
JAGGED
1. Planing wood
SURFACE
with high humidity.
2. Dull knives.
1. Cut too deep.
RIPTING
2. The knives plan
THE SUR-
against
FACE
the direction of the
wood fibers.
3. Dull knives.
1. Dull knives.
COARSE
2. Cut too deep.
/ROUGH
3. Wood moisture too
SURFACE
high.
4. Damaged bearings
knife heads.
1. Inconsistent setting of
UNEQUAL-
knife protrusion.
MODERATE
2. The knife head is not
DEPTH
aligned with the bed
CUT PO
planers.
BOCÍCH
SPECIFICATIONS
Input voltage 230 V
Input frequency 50 Hz
Power consumption 1800 W
Idle speed 10000 min-1
Minimum planing length 250 mm
Maximum planing width 318 mm
Planing height 6-152 mm
Maximum cut per shot 3.2 mm
AXLE
1. Dry the wood.
2. Sharpen the knives.
1. Check for correct
depth of cut.
2. Feed the material
in the direction of the
fibers or
turn the workpiece over.
3. Sharpen the knives.
1. Sharpen the knives.
2. Check the correct
one
depth of cut.
3. Dry the wood.
4. Replace the bearings.
1. Adjust the knife
protrusion.
2. Align the knife head
to the table.
52
Feed speed 7.9m/min
Weight 27 kg
Protection class II.
Sound pressure level measured by
EN 61029:
LpA (sound pressure) 95,3 dB (A) KpA=3
LWA (acoustic power) 108,3 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Use hearing protection whenever the sound pressure
level exceeds 80 dB (A).
Weighted rms acceleration value according to
EN 61029: <2.5 m/s2 K=1.5
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on
the following conditions: Method of power tool use
and type of material being cut or drilled, conditions
of the power tool and method of its maintenance,
appropriateness of the used accessories and ensur-
ing its sharpness and good conditions, the strength
of handle gripping, use of anti-vibration equipment,
suitability of the power tool for the purpose for which
it has been designed and compliance with workflows
according to manufacturer's instructions.
If this power tool is used in an inappropriate manner,
a hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in
all operating modes, e.g. the time when the power
tool is switched off except for the operation time,
and when it idles, i.e. performs no work. This may
substantially decrease the exposition level during the
whole operating cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith theseinstruc-
tions and provide for its proper lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENVIRONMENTAL PROTECTIONWASTE
MANAGEMENT
Power tools, accessories and packaging should
be provided for recycling and not to harm the
environment.

Publicité

loading