Skil MASTERS 1620 Notice Originale page 6

4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR MIXERS
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
• Never use the tool without the protection frames
• Never use the tool in or near an explosive atmosphere
• Never mix combustible substances
• Never reach with your hand or any other object into the
mixing container during mixing
• Wear protective gloves 4, a dust mask 5, close-fi tting
clothes and sturdy shoes
• The noise level when working can exceed 85 dB(A);
wear ear protection 6
• SKIL can assure fl awless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
• Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
• On/off 7
• Switch locking for continuous use 8
! be aware of the forces that occur as a result of
jamming; hold the tool firmly with both hands and
take a secure stance
• Maximum speed control 9
With wheel C 2 the maximum speed can be adjusted
from low to high (1-8)
- switch on the tool
- lock the switch
- turn wheel C to select maximum speed
• Mechanical gear selection 0
- set selector D to desired speed
! actuate the gear selector only when tool is
switched off
1 = LOW SPEED
- high torque
- for mixing high-density substances
2 = HIGH SPEED
- lower torque
- for mixing liquid substances
• Protection frames !
- for protecting the tool
- for putting aside the tool in a simple way
- mount protection frames E before using the tool for
the fi rst time
! never use the tool without the protection frames
• Operating the tool
! ensure that the tool is switched off
- mount mixing paddle G onto spindle F with both a
blade wrench 24 (not standard included) and a
blade wrench 22 @
- connect plug to power source
- ensure the mixing container is securely positioned on
the fl oor
- dip the mixing paddle into the substance to be mixed
- set wheel C 2 in position "1"
- switch on the tool
- gradually increase the mixing speed by turning wheel
C 2 to the desired maximum speed (so that the
substance will not splash around and the tool will not
be overloaded)
! switch the tool off only when the mixing paddle is
in the mixing container
• Holding and guiding the tool #
! while working, always hold the tool at the grey-
coloured grip area(s)
! always hold the tool firmly with both hands
6