DeWalt DW745 Guide D'utilisation page 13

Mitering
WARNING: Miter angles greater
than 45˚ may force the guard into
the saw blade causing damage to
the guard and personal injury. Before
starting the motor, test the operation
by feeding the work piece into the
guard. If the guard contacts the blade,
place the work piece under the guard,
not touching the blade, before starting
the motor.
CAUTION: Certain work piece
shapes, such as molding may not lift
the guard properly. Feed the work piece slowly to start the cut. If the guard contacts the
blade, place the work piece under the guard, not touching the blade, before starting the
motor.
This operation is the same as crosscutting except the miter gauge is locked at an angle
other than 0°. Hold the work piece FIRMLY against the miter gauge and feed the work piece
slowly into the blade (to prevent the work piece from moving). See Figure 29.
Miter Gauge Operation
To set your miter gauge, loosen the lock handle and move the miter gauge to the desired
angle.
Compound Mitering
This is a combination of bevel crosscutting
and mitering. Follow the instructions for both
bevel crosscutting and mitering.
Dust Collection
Your table saw is equipped with a dust shroud
and dust collection port. For best results,
connect a vacuum to the port at the rear of
the saw.
After extended use, the saw's dust collection
system may become clogged. To clear the
dust collection system:
1. Unplug the saw.
2. Turn the saw on its side, so the bottom, open part of the unit is accessible.
3. Open the dust access door (UU) shown in Figure 30 by removing the wing screws (VV).
Clean out the excess dust, and re-secure the access door with the wing screws.
Lubrication
1. All motor bearings are permanently lubricated
at the factory and no additional lubrication is
needed.
2. The height adjustment gear may require
periodic cleaning and lubrication (Fig. 31). If
you have difficulty raising or lowering
the blade, contact a D WALT authorized
E
service center.
FIG. 29
FIG. 30
UU
VV
FIG. 31
Accessories
WARNING: Since accessories, other than those offered by D
tested with this product, use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only D WALT recommended accessories should be used with
E
this product.
If you need assistance in locating any accessory, please contact D
Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D
or visit our website www.dewalt.com.
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect machine from
power source before installing and removing accessories, before adjusting or changing
set-ups or when making repairs. An accidental start-up can cause injury.
Cleaning
WARNING: When cleaning, use only mild soap and a damp cloth on plastic parts. Many
household cleaners contain chemicals which could seriously damage plastic. Also, do not
use gasoline, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products
which may seriously damage plastic parts. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should be performed by a D
service center, a D WALT authorized service center or other qualified service personnel.
E
Always use identical replacement parts.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or workmanship for
E
three years from the date of purchase. This warranty does not cover part failure due to nor-
mal wear or tool abuse. For further detail of warranty coverage and warranty repair informa-
tion, visit www.dewalt.com or call 1-800-4-D
not apply to accessories or damage caused where repairs have been made or attempted
by others. This warranty gives you specific legal rights and you may have other rights which
vary in certain states or provinces.
In addition to the warranty, D WALT tools are covered by our:
E
1 YEAR FREE SERVICE
D WALT will maintain the tool and replace worn parts caused by normal use, for free, any
E
time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D
or Nailer for any reason, you can return it within 90 days from the date of purchase with a
receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For prod-
ucts sold in Latin America, see country specific warranty information contained either in the
packaging, call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-D WALT for a free replacement.
E
11
WALT, have not been
E
WALT Industrial Tool
E
WALT (1-800-433-9258)
E
WALT factory
E
WALT (1-800-433-9258). This warranty does
E
WALT Power Tool, Laser,
E