Rain Gauge - TFA 47.3003 Mode D'emploi

TFA_No_47.3003_Anl_06_20 22.06.2020
MONSUN
– Wireless rain gauge
• In "month/day sequence" the two different date displays can be selected:
month/date (American version) or date/month (European version).
6.3 Reception of outdoor transmitter
• Open the battery compartment of the outdoor rain sensor with a screw driver and
insert the batteries (2 x 1.5 V AA), polarity as illustrated.
• The base station automatically starts scanning the 433 MHz signal to register the rain
sensor unit after setting time. The symbol
successfully. If the reception of outdoor values fails, "- -" appears on the display.
Check the batteries and try it again. Check if there is any source of interference.
• Manual initialization can be helpful. Hold "SEARCH" button on the base station for
3 seconds.
• After successful installation screw up the battery compartment of the transmitter
carefully.
7. How to operate
• Important: Buttons will not function while scanning the outdoor transmitter signal.
• During operation, all successful settings will be confirmed by an acoustical signal.
• The instrument will quit the setting mode, if there is no button used within
15 seconds.
• Holding "▲" or "▼" button, you will enter fast mode.

7.1 Rain gauge

7.1.1 Rain sensor alarm
• When it starts to rain an alarm signal will sound for 2 seconds and the symbol
begins to flash. Press any button to stop the alarm. The display stops flashing
30 minutes after the rain has finished.
Set the acoustic rain sensor alarm on or off during setting mode (see 6.2). "AL ON →
•
AL OF".
• appears on the display when alarm sound is activated.
7.1.2 Indication of date
• Press "SET/RAIN" button to show the date.
7.1.3 Indication of rainfall quantity
• Press "SET/RAIN" button again to show the following information:
• Indication of total rainfall quantity since the last reset. Hold "SET/RAIN" button for
3 seconds to clear the recorded reading.
• Rainfall quantity of the last hour (1H), update every 10 minutes.
• Rainfall quantity of the last 24 hours (24H), update every hour.
• Rainfall quantity of the last rain
rain.
7.1.4 Time and date of recording
• You can recall the time, date and year of recording for every value by pressing
"SINCE" button repeatedly.
7.1.5 Bar graph indication and history
• Press "HISTORY" button to show the bar graph indication of the rainfall quantities
for the last 7 days (DAILY), weeks (WEEKLY) and months (MONTHLY).
12
7:46 Uhr Seite 7
flashes when the signal is received
. The resetting happens with the start of new
MONSUN
– Wireless rain gauge
• Hold "HISTORY" button to recall the value of the current time period (current day,
week or month = 0). Press "HISTORY" button again to recall all single values (1 to 6).
• Press and hold "HISTORY" button and "SINCE" button for 3 seconds at the same
time to reset the memory completely.
7.2 Thermometer
7.2.1 Indoor outdoor temperature
• Press "IN/OUT TEMP/SEARCH" button to show indoor (INTEMP) or outdoor (OUTTEMP)
temperature.
7.2.2 Trend pointer
• The trend pointer displayed on the LCD indicates if the outdoor temperature is
increasing, steady or decreasing.
7.2.3 Maximum/Minimum function
• Press "MAX/MIN" button to show the maximum (MAX) and minimum (MIN) tempe-
rature of the indoor and outdoor sensor one after the other.
• Hold "MAX/MIN" button for 3 seconds to clear the recorded maximum and mini-
mum reading.
7.2.4 Temperature alert
• Press "ALERT" button to set the temperature alert function on or off. (
the LCD if this function is on).
• Hold "ALERT" button for 3 seconds to enter the Alert setting mode. Indoor tempera-
ture flashes. Press "▲" or "▼" button to select indoor or outdoor temperature for
the temperature alert. Press "ALERT" button to confirm the settings. Press "▲" or
"▼" button to set the upper temperature limit (upwards arrow
"ALERT" button to confirm the settings. Press "▲" or "▼" button to set the lower
temperature limit (downwards arrow
• When passing or falling below the selected temperature limit an alarm signal will
sound for 5 seconds and the temperature display begins to flash. The alarm signal
keeps on beeping every minute as long as the temperature is higher/lower than the
preset value (5 times maximum) or the "ALERT" button is pressed.
• Attention: Is the temperature within the preset limits the display stops flashing.
8. Positioning of base station and transmitter
• The outdoor sensor unit should be securely placed on a horizontal surface in an
open area. Avoid trees or other coverings where rainfall may be reduced causing
inaccurate reading.
• Place the base station at the final position. Avoid the vicinity of any interfering field
like computer monitors or TV sets and solid metal objects.
• Check the transmission of the signal from the transmitter to the base station (trans-
mission range 30 m free field), within ferro-concrete rooms, especially with metal
parts, the received signal is naturally weakened.
• If necessary choose another position for transmitter and/or base station.
• With the mountable leg the base station can be placed onto any flat surface or wall
mounted by the wall mounting hole.
9. Care and maintenance
• Clean the instruments with a soft damp cloth. Do not use solvents or scouring agents
• Remove the batteries if you do not use the products for a long period of time.
appears on
is flashing). Press
is flashing).
13