Publicité
Les langues disponibles
Les langues disponibles
Ignitor Lighting
READ INSTRUCTIONS BEFORE LIGHTING.
Do NOT lean over appliance while lighting.
1. Turn OFF
gas burner control valve.
2. Connect LP gas cylinder.
3. Open the grill lid.
4. Press and turn the control knob to the
5. Push and hold ELECTRONIC IGNITOR button until
the burner lights.
6. Once ignited, turn the control knob to the desired
setting.
7. If ignition does not occur in 5 seconds, turn the
burner control knob OFF
, wait 5 minutes, and
repeat lighting procedure.
If ignition still does not occur, follow match-lighting
instructions.
Match-Lighting
Do NOT lean over appliance while lighting.
1. Turn OFF
gas burner control valve.
2. Open grill lid.
3. Connect LP gas cylinder
4. Insert match into match holder. Strike match. Place lit
match into match light hole at the rear of the grill
bottom, shown "A". Make sure lit match is placed
inside through the hole and near burner.
5. Push in and turn control knob to position 5 . Be
sure burner lights and stays lit.
6. If ignition does not occur in 5 seconds, turn the burner
control knob OFF
, wait 5 minutes, and repeat
lighting procedure.
A
Rotate Match
Light Hole
Cover
CAUTION
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER
If your appliance is getting hard to light or the flame
is weak, check and clean the venturis and burners.
Spiders or small insects are known to create
"flashback" problems by building nests and laying
eggs in the appliance's venturi or burner obstructing
the flow of gas. The backed-up gas can ignite behind
the control panel. This flashback can damage your
appliance and cause injury. To prevent flashbacks
and ensure good performance, the burner and
venturi tube assembly should be removed and
cleaned whenever the appliance has been idle for an
extended period of time.
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts
of burner assembly or if you have trouble igniting
appliance.
1. Turn gas control knob to
cartridge.
2. Open top cover, remove cooking grate and warming
rack, shown A. This will expose the burner from
inside, shown B.
position.
3. Remove 3 screws attaching burner, shown C
4. From the top of the grill, carefully lift burner out,
shown D.
5. Clean any blocked ports with a stiff wire such as an
open paper clip.
6. Clean burner as recommended below, shown E.
We suggest three ways to clean the burner tube.
Use the one easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works
well) into a small hook. Run hook through burner
tube several times.
(B) Use a narrow bottle brush with a flexible handle (do
not use a brass wire brush), run the brush through
burner tube several times.
(C) Wear eye protection: Use an air hose to force air
into the burner tube and out the burner ports.
Check each port to make sure air comes out each
hole.
7. Check burner for damage, due to normal wear and
corrosion some holes may become enlarged. If any
large cracks or holes are found replace burner.
8. Insert burner into firebox .
VERY IMPORTANT: Burner tube must re-engage
over valve
opening. See illustration, shown F.
9. Reattach burner with screws removed in step 3.
10. Reinstall heat tent, cooking grates and warming
Match Light
rack.
Hole
Ensure Cooking Grate ridges run front to back (fig.A)
Warming
Warming
Rack
Rack
View is from
rear of
appliance
Burner
Screws
Tube cleaner
(see above
recommendations)
Burner
(removed)
Leak Testing Valves, Tube and
Regulator
Leak test at least once a year and every
time the cartridge is changed or
disconnected.
1. Turn appliance control knobs to
2. Be sure gas cartridge is tightly connected to
regulator.
3. Turn on Gas. If you hear a rushing sound, turn
gas off immediately. There is a major leak at
the connection. Correct before proceeding.
4. Brush soapy solution (mixture of half soap and
half water) onto hose connections and areas
circled below.
5. If growing bubbles appear, there is a leak. Check
cartridge for tigthness. If leak continous relace
cartridge and try again. If leak cannot be
stopped do not try to repair. Call for replacement
parts.
and remove
B
A
Warming
Rack
Burner
(exposed)
Cooking
Grate
Move burner to rear
D
C
and upward
Burner
E
F
Tube
Orifice
Orifice engaged inside burner
tube end correctly
.
3
Storing Your appliance
•Clean cooking grates.
•Store in dry location.
•When gas cartridge is connected to appliance, store
outdoors in a well-ventilated space and out of reach
of children.
•Cover appliance if stored outdoors.
•Store appliance indoors ONLY if gas cartridge
disconnected, removed from appliance and stored
outdoors.
•When removing appliance from storage check for burner
obstructions.
General appliance Cleaning
•
Clean appliance often, preferably after each
cookout. If a bristle brush is used to clean any of the
appliance cooking surfaces, ensure no loose bristles
remain on cooking surfaces prior to grilling. It is not
recommended to clean cooking surface while
appliance is hot.
appliance should be cleaned at least once a year.
•Do not mistake brown or black accumulation of
grease and smoke for paint. Interiors of gas grills
are not painted at the factory (and should never be
painted). Apply a strong solution of detergent and
water or use a appliance cleaner with scrub brush on
insides of appliance lid and bottom. Rinse and allow
to completely air dry. Do not apply caustic
appliance/oven cleaner to painted surfaces.
• Plastic parts: Wash with warm soapy water and wipe
dry.
Do not use citrisol, abrasive cleaners, degreasers or
a concentrated appliance cleaner on plastic parts.
Damage to and failure of parts can result.
•Porcelain surfaces: Because of glass-like
composition, most residue can be wiped away with
baking soda/water solution or specially formulated
cleaner. Use nonabrasive scouring powder for
stubborn stains.
•Painted surfaces: Wash with mild detergent or
nonabrasive cleaner and warm soapy water. Wipe
dry with a soft nonabrasive cloth.
•Stainless steel surfaces: To maintain your
appliance's high quality appearance, wash with mild
detergent and warm soapy water and wipe dry with
a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic
cleaning pad. Use only in direction of brushed finish
to avoid damage. Do not use abrasive pad on
areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean
any of the appliance cooking surfaces, ensure no
loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking
surfaces while appliance is hot.
IF APPLIANCE FAILS TO LIGHT
Make sure gas is turned on at cartridge.
Make sure there is gas in the cartridge.
Does the ignitor make a sparking Noise?
If yes check for spark at burner.
If no spark check for damaged or loose wires.
If wires are OK check for cracked or broken electrode,
replace if needed.
If wire or electrodes are covered by cooking residue,
clean electrode tip with alcohol wipe if needed.
If needed replace wires.
If no sound check battery.
Make sure battery is installed correctly.
Check for loose wire connection at module and switch.
If ignitor continues to not work then use match.
If this appliance needs to be repaired please contact
your supplier or Kriswell A/S. Please see Kriswell A/S
contact information on page 32.
B
Høyre
skinne
Publicité
