Publicité
Les langues disponibles
Les langues disponibles
WARNING
!
•
Ensure the appliance is completely cool before starting installation.
•
To avoid danger of suffocation, keep the packaging bag away from babies and children. Do not use in cribs,
aub - aSCent univerSal blower inStallation inStruCtionS
beds, carriages, or play pens. This bag is not a toy. Knot before throwing away.
aub - aSCent univerSal blower inStallation inStruCtionS
1. Remove the safety barrier by lifting it up and off the appliance.
2. Remove the door from the appliance by releasing the four latches.
ENsurE THE uNiT is cOmPlETEly cOOl BEfOrE sTarTiNG iNsTallaTiON.
ENsurE THE uNiT is cOmPlETEly cOOl BEfOrE sTarTiNG iNsTallaTiON.
note:
TO aVOid daNGEr Of suffOcaTiON KEEP THE PacKaGiNG BaG aWay frOm BaBiEs aNd cHildrEN.
TO aVOid daNGEr Of suffOcaTiON KEEP THE PacKaGiNG BaG aWay frOm BaBiEs aNd cHildrEN.
It may be necessary to move the control module aside during blower installation (electronic only).
dO NOT usE iN criBs, BEd, carriaGEs Or Play PENs. THis BaG is NOT a TOy. KNOT BEfOrE
dO NOT usE iN criBs, BEd, carriaGEs Or Play PENs. THis BaG is NOT a TOy. KNOT BEfOrE
3. Attach the two 1/4" connectors (black and white) from the wire harness to the thermodisc.
a.
Remove the screen by lifting it up and off of the appliance.
4. Attach the two 1/4" connectors (black and red) from the wire harness to the blower.
a.
Remove the screen by lifting it up and off of the appliance.
B.
Remove the door from the appliance by releasing the four latches.
5. Install the clear bumpers (supplied) onto the bottom of the blower to avoid the blower rubbing against the
B.
Remove the door from the appliance by releasing the four latches.
c.
It may be necessary to move the control module aside during blower installation. (Electronic Only)
c.
It may be necessary to move the control module aside during blower installation. (Electronic Only)
floor of the appliance.
d.
Attach the two 1/4" connectors (black and white) from the wire harness to the thermodisc.
d.
Attach the two 1/4" connectors (black and white) from the wire harness to the thermodisc.
6. Pivot the blower into the bottom of the appliance, ensuring the gasket remains in place between the blower
E.
Attach the two 1/4" connectors (black and red) from the wire harness to the blower.
E.
Attach the two 1/4" connectors (black and red) from the wire harness to the blower.
and outer shell while sliding the blower against the left side of the outer shell into the blower mounting tab.
f.
Install the clear bumpers supplied onto the bottom of the blower to avoid the blower rubbing against the floor of
f.
Install the clear bumpers supplied onto the bottom of the blower to avoid the blower rubbing against the floor of
Secure in place using one screw (Fig. 1 and 2).
the appliance.
the appliance.
G.
Pivot the blower into the bottom of the appliance. Ensure the gasket remains in place between the blower and
note:
G.
Pivot the blower into the bottom of the appliance. Ensure the gasket remains in place between the blower and
outer shell while sliding the blower against the left side of outer shell into the blower mounting tab. Secure in place
outer shell while sliding the blower against the left side of outer shell into the blower mounting tab. Secure in place
With the zip tie supplied, ensure all wires remain clear of the blower.
using one screw, see Figures 4 and 5.
using one screw, see Figures 4 and 5.
NOTE: WiTH THE ZiP TiE suPPliEd, ENsurE all WirEs rEmaiN clEar Of THE BlOWEr.
NOTE: WiTH THE ZiP TiE suPPliEd, ENsurE all WirEs rEmaiN clEar Of THE BlOWEr.
fiGURe 4
fiGURe 4
SCREW
SCREW
LOCATION
LOCATION
H.
Place the control module back into its original position. Ensure the transformer is plugged into the rear outlet of
7. Place the control module back into its original position. Ensure the transformer is plugged into the rear outlet
H.
Place the control module back into its original position. Ensure the transformer is plugged into the rear outlet of
the electrical box, refer to Figure 2.
of the electrical box.
the electrical box, refer to Figure 2.
i.
The variable speed switch (VSS) will need to be disassembled to secure to the VSS bracket for installation. Place
8. The variable speed switch (VSS) will need to be disassembled to secure to the VSS bracket for installation.
i.
The variable speed switch (VSS) will need to be disassembled to secure to the VSS bracket for installation. Place
the VSS through the mounting bracket using the lock washer to secure it in place. Take the variable speed switch
Place the VSS through the mounting bracket using the lock washer to secure it in place. Take the variable
the VSS through the mounting bracket using the lock washer to secure it in place. Take the variable speed switch
knob and install into position. (Refer to Figure 6.)
speed switch knob and install into position (Fig. 3).
knob and install into position. (Refer to Figure 6.)
J.
To install the variable speed switch, the mounting bracket will first need to be installed. Remove the two screws
J.
To install the variable speed switch, the mounting bracket will first need to be installed. Remove the two screws
9. To install the variable speed swtich, the mounting bracket will first need to be installed. Remove the two
securing the piezo ignitor switch bracket in place. Install the VSS mounting bracket into position then reinstall
securing the piezo ignitor switch bracket in place. Install the VSS mounting bracket into position then reinstall
screws securing the piezo ignitor switch bracket in place. Install the VSS mounting bracket ito position then
the two previously removed screws, refer to Figure 6.
the two previously removed screws, refer to Figure 6.
reinstall the two previously removed screws (Fig. 3).
FIGURE 6
FIGURE 6
VSS
VSS
BRACKET
BRACKET
K.
Plug the connector from the variable speed switch to the matching connection on the wire harness.
K.
Plug the connector from the variable speed switch to the matching connection on the wire harness.
l.
For installation of the thermal disc bracket, bend the tab on the bottom of the firebox 90 degrees. This will be
10. Plug the connector from the variable speed switch to the matching connection of the wire harness.
l.
For installation of the thermal disc bracket, bend the tab on the bottom of the firebox 90 degrees. This will be
the mounting tab for the thermal disc bracket, see Figure 7.
11. For installation of the thermal disc bracket, bend the tab on the bottom of the firebox 90 degrees. This will be
the mounting tab for the thermal disc bracket, see Figure 7.
m.
Bend the thermal disc bracket 90 degrees and secure it to the firebox mounting tab using the two screws supplied,
the mounting tab for the thermal disc bracket (Fig. 4).
m.
Bend the thermal disc bracket 90 degrees and secure it to the firebox mounting tab using the two screws supplied,
refer to Figure 7. Ensure that the thermal disc is in contact with the firebox base and that the wire harness is
12. Bend the thermal disc bracket 90 degrees and secure it to the firebox mounting tab using the two screws
refer to Figure 7. Ensure that the thermal disc is in contact with the firebox base and that the wire harness is
properly attached.
supplied (Fig. 4). Ensure that the thermal disc is in contact with the firebox base and that the wire harness is
properly attached.
N.
Plug the power cord from the blower into the electrical box, refer to Figure 2.
properly attached.
N.
Plug the power cord from the blower into the electrical box, refer to Figure 2.
NOTE: The blower is thermally activated, so when it is turned on, it will automatically start approximately 15
13. Plug the power cord from the blower into the electrical box.
NOTE: The blower is thermally activated, so when it is turned on, it will automatically start approximately 15
minutes after lighting the appliance and will run for approximately 30 minutes after the appliance has been turned
minutes after lighting the appliance and will run for approximately 30 minutes after the appliance has been turned
note:
off.
off.
The blower is thermally activated, so when it is turned on, it will automatically start approximately 15 minutes
To view a video of This insTallaTion visiT oUR weBsiTe aT: www.napoleonfireplaces.com/support/
To view a video of This insTallaTion visiT oUR weBsiTe aT: www.napoleonfireplaces.com/support/
after lighting the appliance and will run for approximately 30 minutes after the appliance has been turned off.
NOTE: fOr mOrE dETailEd iNsTrucTiONs rEfEr TO yOur iNsTallaTiON maNual.
NOTE: fOr mOrE dETailEd iNsTrucTiONs rEfEr TO yOur iNsTallaTiON maNual.
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada
11.0 optional blower installation
WARNING
WARNING
!
!
THrOWiNG aWay.
THrOWiNG aWay.
BLOWER
BLOWER
MOUNTING TAB
MOUNTING TAB
Fig. 1
LOCATION
LOCATION
PIEZO IGNITOR
PIEZO IGNITOR
BRACKET
BRACKET
Fig. 3
• (705)721-1212
• (705)721-1212
fiGURe 5
fiGURe 5
BLOWER
BLOWER
BLOWER
BLOWER
fiGURe 7
fiGURe 7
THERMAL DISC
THERMAL DISC
THERMAL DISC
THERMAL DISC
MOUNTING TAB
BRACKET
MOUNTING TAB
BRACKET
• fax (705)720-9081
• fax (705)720-9081
REAR VIEW
REAR VIEW
REAR VIEW
REAR VIEW
BLOWER
BLOWER
BLOWER
BLOWER
MOUNTING
MOUNTING
MOUNTING
MOUNTING
Fig. 2
TAB
TAB
TAB
TAB
FIREBOX BASE
FIREBOX BASE
Fig. 4
W415-1479 / A / 05.09.16
W415-1479 / A / 05.09.16
• www.napoleonfireplaces.com
• www.napoleonfireplaces.com
W415-2881 / C / 03.07.22
EN
59
Publicité
