fadini Junior 650 Notice D'instructions page 27

JUNIOR 633
JUNIOR 650
ATTENTION: the installation of this electronic control board requires a specific technical knowledge and must be carried out by
professionally qualified people and habilitated according to the safety norms in force. It is important that these instructions be
!
carefully read and followed to avoid that the electronic control board be used and/or installed in the wrong way.
The ELPRO 65 electronic programmer was conceived and manufactured for the managements of the Junior 633 and Junior 650
electromechanical sliding operators with 230 Vac motors. Any other use different from that specified in this instruction booklet is to
be considered prohibited.
Meccanica Fadini declines any responsibility for damage caused to properties or persons due to possible incorrect installations or
failure of the system to comply with the applicable regulations; it is compulsory that the machinery directive 2006/42/CE be
implemented. Maintenance or inspections to assess the product status must be carried out by qualified and professionally trained
technicians.
Before any servicing is made to the board, disconnect mains power supply. It is also recommended that the Safety Norms manual be
read, available from Meccanica Fadini on request. The manufacturing company does not take any liability for improper use of the
electronic control board.
CE DECLARATION OF CONFORMITY of the manufacturer:
Meccanica Fadini snc (Via Mantova, 177/A - 37053 Cerea - VR - Italy) declares under own responsibility that Elpro 65 complies with the
2006/42/CE Machinery Directive, and also that it is sold to be installed in an "automatic system", along with original accessories and
components as indicated by the manufacturing company. The manufacturer is not liable for possible incorrect use of the product. The product
complies with the following specific norms: Low Voltage Directive 2014/35/UE, Electromagnetic Compatibility Directive 2014/30/UE. In order
to certify the product, the Manufacturer declares under own responsibility the compliance with the EN 13241-1 PRODUCT NORMS.
General description: The Elpro 65 is a PCB card with microprocessor for the command and management of the Junior 633 and Junior 650
sliding gate opener with programming for self-learning of the different movement phases of the gate. Power supply: 230 V ±10% 50 Hz
single-phase. Logic operation: given the open command impulse, it performs the function for open, pause, close in automatic or
semi-automatic with programmable slowdown, possibility of step by step radio command, radio no reverse on opening, with or without
pre-flashing, reverse run upon contact with an obstacle and LED diagnostics. Rh and Lh installations are made selectable by dip-switch,
blue/amber LED diffuser on the cover casing for the gate opener status signal.
DIAGNOSTIC LED: LED status during proper operation of the system, the green LEDs must always be on; the red LEDs must always be
off.
L2 (green on) = photocells, turns off with obstacle present.
L4 (red off ) = open, lights up with the opening command impulse.
L5 (red off ) = close, lights up with the closing command impulse.
L6 (green on) = stop, goes off with the stop command impulse.
L7 (red off ) = radio, lights up with each transmitter impulse.
L10 (red off ) = lights up in case of short circuit with 24 Vdc. Goes off when circuit problem is corrected.
L20 (red off ) = pedestrian, lights up with the open command for pedestrians.
L21 (green on) = photocell or safety edge in open, turns off in case of obstacle.
nd
L22 (green on) = 2 Junior input.
L24 (green on) = safety edge in closing, turns off in case of obstacle.
LP (red off ) = program led, it lights on in phase of programming.
X (red) = led limit switch, always alight during the movement.
Y (red) = led limit switch, always alight during the movement.
LED X on
LED Y off ff
LED X off ff
LED Y on
DIP-SWITCH: enables the performance of all of the possible functions of the Junior 633 and Junior 650 sliding gate opener.
1 = OFF: Photocell does not stop gate in opening
2 = OFF: Radio stops and reverses in opening
3 = OFF: Semiautomatic operation
4 = OFF: Without pre-flashing before opening
5 = OFF: Radio reverses direction on every impulse
6 = OFF: Slowdowns (to be programmed)
7 = OFF: Activates "reverse": running is reversed upon contact
8 = OFF: Flasher on in pause
9 = OFF: No closing after passage by the photocell
10 = OFF: No DSA control on the photocells
11 = OFF: Junior 633/Junior 650 installed on the left
12 = OFF: Single Elpro 65,
or 1 st Junior 633/Junior 650 as MASTER
ELPRO 65
Junior Sx
Fully Open
Junior Sx
OFF ON
27
Fully Open
1 = ON: Photocell stops gate in opening
2 = ON: Radio does not reverse (and does not stop)
in opening
3 = ON: Close in automatic after pause time
4 = ON: Pre-flashing before opening
5 = ON: Radio switch: open-stop-close-stop
6 = ON: No slowdowns
7 = ON: No direction reversing upon contact
8 = ON: Flasher off in pause
9 = ON: Closing after passage by the photocell
10 = ON: DSA photocell control before start up
11 = ON: Junior 633/Junior 650 installed on the right
12 = ON: Elpro 65 SLAVE, 2 nd Junior 633/Junior 650
Meccanica Fadini s.n.c.
Director in charge
LED on
LED off
Junior Dx
Junior Dx