Texas A/S XT Serie Manuel De L'utilisateur page 16

Only use orginal spare parts or accessories. If not
orginal parts or accessories is used, the liablility is
no longer applied.
Miscellaneous
The motor is not pre-filled with oil.
Always before start check the engine oil level.
Factory-fitted control devices, such as the handle-
mounted clutch cable, must not be removed or
exposed.
Only drain the fuel tank outdoors. Gasoline is
extremely flammable and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.
Waste electrical products must not be
disposed of with the household waste. This
tool should be taken to your local recycling
centre for safe treatment.
The lawnmower is manufactured according to the latest
safety requirements. These include a blade brake that
stops the motor and blade in 3 seconds when the blade
brake. Every precaution is only effective when it is
followed exactly. Use the following description when
you mount your lawnmower.
Identification of the parts
See Illustration ID
Notice: the illustrations may vary from your present
model
A. Handlebar for drive *
B. Handlebar for engine brake
C. Recoil starter
D. Wing nut
E. Rear discharge guard with spacer block *
F. Water nozzle
G. Grass collector
H. Gasoline filling cap
I. Air Filter
J. Exhaust
K. Spark plug
L. Oil cap
M. Electric starter
N. Panel *
O. Throttle/Choke lever *
P. Height adjustment
Q. Side discharge guard *
R. Primer *
* may vary from your actual model.
Mounting
Unpacking: Illustration M1
Remove the mower from the box by pulling the machine
out from the side. The box contains:
1 pcs mower
2 pcs wing nut set consisting of wing nuts, bolts
and washers. (See ID; D)
1 pcs spacer block (See ID; E)
Warning: Ensure that cables are not pinched.
Handlebar and height adjustment: Illustration M2
The handlebars are height adjustable. This means that
they can be adjusted so that it best fits you. Before you
install the handlebar, it may be a good idea to have
decided which height is best for you.
1. Attach the lower handlebar tubes as shown and
fasten with screws.
2. Attach the upper handlebar on the lower. Fasten
with wing nut from the inside of the handlebar.
3. Customize cable and secure with cable clamp.
Mounting the engine brake cable: Illustration M3
1. Gently push the top handlebar ID:B forward
2. Insert the engine brake cable from the outside, into
the hole in the bracket on handlebar ID:B and lock.
Mounting the drive cable: Illustration M3
1. Gently push the lower handlebar ID:A downward
2. Insert the drive cable from the inside, into the hole
in the bracket on handlebar ID:A and lock.
Mounting the recoil-starter: Illustration M4
1. Pull the engine brake handlebar and hold, in order
to release the starter cord on the engine.
2. Pull gently the starter cord from the engine
(Engine brake handlebar MUST be hold)
3. Attach the starter grip on the rack of handlebar.
4. Release the engine brake handlebar and the
starter grip.
Mounting the panel: illustration M5*
1. For models with panel with cup holder follow
illustration M5-1
2. For models with panel follow illustration M5-2
*Note: Not all models do have panel.
Mounting the grass collector: Illustration M6
1. Click the frame to the grass collector.
The grass collector comes with a handy indicator
showing whether the box is full of grass and needs
emptying.
Rear discharge guard: Illustration M7-1
If you want to mow without grass collector it is important
to attach the two spacer blocks.
1. Insert the spacer block (ID:E) under the rear
discharge guard.
Note: The spacer block is for rear ejection only!
Otherwise it should be removed.
Warning: If the spacer block is not mounted. The
mower will have difficulties to dispose the grass.
Mulching plug: Illustration M7-2
1. Open side discharge guard, if you want to mow
with mulching functionality.
NB Don't use the grass collector
Side discharge guard: Illustration M7-3*
1. Open side discharge guard.
NB Don't use the grass collector
* Note: Not all models do have side discharge guard
16