Metabo HPT C 3610DRA Instructions De Sécurité Et Mode D'emploi page 3

9. ALWAYS WEAR EYE PROTECTION WITH SIDE
SHIELDS THAT MEETS THE REQUIREMENTS OF
ANSI STANDARD Z87.1 WHEN WORKING WITH
THE TOOL TO PREVENT EYE INJURY. Ordinary
eyeglasses do not provide adequate protection
because they do not contain impact resistant safety
glass. Also, use a face mask for additional safety and
wear a dust mask if the cutting operation produces
dust.
10. ALWAYS SECURE THE WORKPIECE TO THE
FENCE OR THE TABLE. Use clamps or a vise to hold
the workpiece in place. It is safer than using your hand
and it frees both hands to operate the tool.
11. NEVER OVERREACH. Always keep proper footing
and balance when working with the tool.
12. ALWAYS MAINTAIN TOOLS WITH CARE. Always
keep tools sharp and clean for the best and safest
performance. Always follow instructions for lubricating
the tool and for changing accessories.
13. ALWAYS DISCONNECT THE TOOL before servicing
and before changing blades or other accessories.
14. ALWAYS USE RECOMMENDED ACCESSORIES
ONLY WHEN OPERATING THIS TOOL.
Consult this instruction manual for descriptions
of recommended accessories. To avoid personal
injuries, use only recommended accessories in
conjunction with this tool.
15. NEVER STAND ON THE TOOL. Prevent serious
injury by not tipping the tool and by not risking
unintentional contact with the saw blade.
16. ALWAYS CHECK FOR DAMAGED PARTS BEFORE
USING THE TOOL. Always check the guard and all
other components for damage before using the tool
to assure that they will function properly. Check all
moving parts for proper alignment, freedom from
binding and other conditions that might aff ect proper
operation. Always repair or replace any damaged
guards or other damaged components before using
the tool.
17. ALWAYS CONFIRM THE ROTATION DIRECTION
OF THE BLADE BEFORE USING THE TOOL.
Always feed work into the tool against the rotation
direction of the blade in order to prevent possible
injury.
18. NEVER LEAVE THE TOOL RUNNING WHILE
UNATTENDED. TURN POWER OFF. Do not leave
tool until it comes to a complete stop. Always turn the
power off when the tool is not in use. Always unplug
the power cord when the tool is not in use.
19. This tool was not designed to be used for mass-
production applications and should not be used in
mass-production environments.
20. Never raise the saw blade from the workpiece until it
has fi rst come to a complete stop.
21. Always use outboard stands to provide support for
long workpieces that overhang the table of the slide
compound miter saw.
22. Always return the carriage to the full rear position after
each crosscut operation in order to reduce the risk of
injury.
23. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.
BATTERY TOOL USE AND CARE
1. Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack
into power tools that have the switch on invites
accidents.
2. Recharge only with the charger specifi ed by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fi re when used
with another battery pack.
3. Use power tools only with specifi cally designated
battery packs. Use of any other battery packs may
create a risk of injury and fi re.
4. When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fi re.
5. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6. Disconnect battery pack from tool or place the
switch in the locked or off position before making
any adjustments, changing accessories, or
storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
SERVICE
1. Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
English
3