Wood's SILENT Guide D'instructions page 8

Operating Instructions
GB
WOOD'S, ONE OF THE WORLD'S
LEADING DEHUMIDIFIERS
Wood's dehumidifier products have
been known as market leaders for many
years. Wood's dehumidifiers are suitable
for use in the most demanding climates,
even in region with lower temperatures
or humidity levels. They are designed to
perform in any places that can become
damp such as cellars, garages or summer
house. They are also excellent for drying
laundry, attics or pool rooms (refer to
specific regulations). They are some of the
most energy efficient dehumidifiers even
at lower temperatures or humidity levels.
They do not wear out clothes.
The amount of humidity that the
dehumidifier removes depends on the
temperature, the humidity level and its
placement. External weather conditions
may also affect the performance of
the dehumidifier. In cold weather the
absolute humidity in the air decreases and
therefore the extraction of humidity by
the dehumidifier is reduced. (The relative
humidity might still be on a high level.)
The dehumidifier is suitable for use in the
temperature range +2˚C to +35˚C.
Wood's dehumidifiers are safe to operate
and intended for continuous use over
many years.
EXCESSIVE AIR HUMIDITY – A DANGER
Condensation occurs when water vapour
in the air comes into contact with a cold
surface such as cold window or wall.
When water vapour is cooled down,
condensation occurs, and water-drops
are formed. In highly humid air, the air
may get musty and mould might get
formed, causing damages to a house and
its furniture. This environment may even
cause illness for the residents. Mites and
spiders also develops more in a damp
environment. A dehumidifier with high
performance creates a good, healthy
humidity level. For greatest efficiency
the doors and windows of rooms that
are being dehumidified should be kept
closed. Removes odours, dries wood
and removes moisture from sportsware
outdoors equipment.
8
A dehumidifier may be used in cellars,
washrooms, garages, crawl spaces,
caravans, summer-houses and on
boats. If the humidifier is kept in colder
environments, you should study the Hints
at the end of the manual.
PLACEMENT OF THE DEHUMIDIFIER
Wood's dehumidifiers are easy to move
around, all you need to have is a power
source for 220/240V, but bear in mind the
following:
- The dehumidifier should not be placed
near radiators or other heat sources or
exposed to direct sunlight, as it will reduce
performance.
- It is necessary to heat up a room and keep
the temperature above +2˚C.
- To maximise the air flow, the dehumidifier
should stand at least 25cm from a wall or
any other obstruction.
- Ideal is to put it in the center
of the room / area.
NOTE: When placed in a shower or
bathing area, the dehumidifier should
be fixed in place. It is compulsory to
check and respect your local bathroom
electrical regulations before use.
USING THE DEHUMIDIFIER
If the dehumidifier is transported
horizontally, oil may have run out of
the compressor and into the closed
piping system. In such a case, let the
dehumidifier stand for a few hours before
being used. It is very important that
the oil runs back into the compressor,
otherwise the dehumidifier may be
seriously damaged.
1. Check that the water reservoir is correctly
placed and the float moves freely in the
reservoir. See the section on the Float.
2. Connect the dehumidifier to an grounded
power source.
3. Select fan speed. (This does not apply to
SW20FW)
4. Set the desired humidity level by rotating
the hygrostat. See the section on the
hygrostat.
NOTE: When the dehumidifier
is turned off, it will take 5 minutes
before the dehumidifier is restarted,
the built-in automatic functions are
deactivated, during this period.
THE FLOAT
The float consists of a white plastic
cylinder which hangs on two arms.
The float rests on the surface, so it is
lifted when the water level rises. When
the float reaches a certain height, the
dehumidifier responds to this and shuts
down automatically to prevent flooding
of the tank.
When you have emptied the water
reservoir and are to replace it in the
dehumidifier follow these steps:
1. Push the water reservoir in until it
touches the float.
2. Raise the forward edge of the water
reservoir from below so that the whole
water reservoir is slightly slanted.
3. Push the water reservoir home. The
float should now be in the reservoir
instead of being stuck behind it.
NOTE: It is important that the float
moves freely, since its purpose is to
respond to the water level and ensure
that the dehumidifier is turned off when
it is high. A wrongly placed float may
allow the water reservoir to flood.
05
04