Husqvarna TS300E Manuel D'utilisation Et D'entretien page 33

10 Bevel cutting
( )
SEE FIG. 9
• Slacken off nut (4) using spanner (5).
• Swivel or slant the head.
• Tighten nut (4) using spanner (5).
11 Maintenance (the motor must be stopped)
• Clean the machine regularly.
• Drain the tank frequently to remove cutting residue,
which otherwise could block the pump and cause it to
wear out prematurely.
• Carefully clean the contact faces for the table rollers.
Store in a dry place, not accessible to
children.
!
Maintain the tools carefully.
FAULT FINDING
In the event of faulty operation refer to the tables below
to find a solution.
• The machine does not work
CAUSES
Not plugged in properly
or cable damaged
No mains voltage
Switch defective, motor
cable damaged
Motor faulty (no power,
unpleasant smell)
• Difficult starting
CAUSES
Single phase motor star-
ting condenser
Three-phase supply not
correct (on 2 phases,
motor cable faulty)
• The pump does not start
CAUSES
The mains lead is not
correctly connected or is
damaged
No voltage in pump circuit
or mains supply circuit
• The pump does not pump water
CAUSES
An air bubble may have
formed inside the pump
body
The turbine is jammed
REMEDIES
- Make sure that the supply
is correctly plugged in
(plug, extension lead, etc)
- Check the supply cable
- Test or have tested by
an electrician (circuit
breaker, plug, etc)
- Have tested by an elec-
trician or contact the
service department
- Contact the service
department to have the
motor replaced
REMEDIES
- Replace the
condenser
- Have it checked by an
electrician or contact
the service department
REMEDIES
- Check the mains lead
- Check the pump circuit
and mains supply circuit
REMEDIES
- Holding the pump of the
outlet pipe remove it from
the water and reimmerse it
- Unscrew the filter and,
using a small screwdri-
ver, remove all dirt from
the operating area of
the turbine.
12 Adjustments
• The machine is set before leaving the factory and no
adjustment is necessary.
• Ø 300 and Ø 350 adaptation (SEE FIG. 11)
A = Ø 300
B = Ø 350
13 Important advice
• Retighten the nuts and bolts periodically.
• In the event of a long period of use pay special atten-
tion to the maintenance and protection of the disc.
• Make sure that sufficient water is sprayed onto the disc.
• Tighten the disc correctly.
• Make sure that the contact faces of the disc, the
flanges and the spindle are clean.
The manufacturer declines all responsibili-
ty for loss or damage resulting from misu-
!
se or any modification, alteration or powe-
ring that does not conform to the manu-
facturer's original specifications.
At the work station, the sound pressure
level may exceed 85 db (A)
In this case individual protection mea-
sures must be taken.
14 Repairs
S
Contact your supplier who is entirely at your
A service to carry out repairs in the shortest
time at the best possible price.
V
15 Spare parts
For rapid delivery of spares and in order to avoid any
wasted time, it is necessary to remind your supplier of
the details shown on the instruction plate on the machi-
ne with each order, as well as the reference of the part
to be replaced.
00000000
Item numberCode
See exploded view
16 Scrapping
In the event of deterioration and scrapping
of the machine, the following items must
!
be disposed of in accordance with the
requirements of the legislation in force.
• Main materials :
Motor : Aluminium (AL), Steel (AC),
Motor : Copper (CU), Polyamide (PA)
Machine : Steel sheet (AC), Cast iron (FT)
The instructions for use and spare parts found in this
document are for information only and are not binding.
As part of our product quality improvement policy, we
reserve the right to make any and all technical modifi-
cations without prior notice.
(0)
Quantity
16