Husqvarna TS300E Manuel D'utilisation Et D'entretien page 31

This symbol indicates that the machine is in
conformance with the applicable European
directive.
SPECIAL INSTRUCTIONS
The disc cutter is designed to provide safe and reliable
service in operating conditions corresponding with the
instructions, but it can present dangers for the user and
risks of damage, consequently regular on site inspection
is necessary to ensure :
• Perfect technical condition (use for the purpose for
which it is intended and taking into account any risks,
and correction of any malfunction detrimental to safety).
• Use of a diamond disc for water lubricated cutting of
marble, stone, granite, brick and facings (porcelain,
glazed tiles, ceramics, etc). The use of any other disc
is forbidden (abrasive, saw, etc).
• Competent personnel (qualifications, age, training,
education) who have studied the manual in detail
before starting work: any fault of an electrical or other
nature must be checked by a competent person (elec-
trician, maintenance foreman, authorized dealer, etc).
• That the warnings and instructions marked on the
machine are followed (adequate personal protection,
correct use, general safety instructions, etc).
• That no modification, transformation or addition is
detrimental to safety and that it is carried out without
prior authorization from the manufacturer.
• Respect of the maintenance intervals and periodical
checks recommended.
• That only genuine spare parts are used for repairs.
Instruction plate
MANUFACTURER
TYPE TYPE
WEIGHT
MASSE UTILE Kg
MAXI TOOL Ø MAXI OUTIL mm
BORE Ø ALESAGE mm
SPEED T/MN - RPM
1 Use
• Use : Sawing marble, stone, granite, brick, cement
and all facings (porcelain, glazed tiles, ceramics, etc).
• Tools : Water lubricated diamond disc
T
diameter 300 mm - diameter 350xmm
AL
(D)- bore 25.4 mm (AL).
(Information from your usual supplier).
D
Carborundum
disc
Any application not corresponding with the inten-
ded use (use of a saw blade, abrasive disc, etc) is
prohibited.
2 Technical specifications
POWER VOLTAGE
± 5 %
2,2 kW (3CV) 230 V 50 Hz
2,9 kW (4CV) 400 V 50 Hz
• Motor speed : 2800 rpm
• Disc speed : 2800 rpm
• Electrical protection : IP 55
N° SERIE SERIAL
FABRICATION
ANNEE DE
FABRICATION YEAR
POWER
PUISSANCE kW
PLAGE DE
V VOLTAGE
TENSION
FREQUENCE Hz FREQUENCY
INT. UTIL. A INTENSITY
Saw blade
CURRENT PUMP
10 A 13 W 230 V
11,5A 13 W 230 V
• Depth of cut (E) :
- at 90° : Ø 350 = 100mm - at 45° : Ø 350 = 65mm
- at 90° : Ø 300 = 75mm - at 45° : Ø 300 = 45mm
• Length of cut (L) : E = 15 - 610mm
: E = 50 - 570mm
• Useable width (to the right)) (l) : 310mm.
• Dimensions (mm) L x l x h :
- 1120 x 620 x 1230 (with legs)
- 1120 x 620 x 650 (bench)
• Unladen weight : ± 80 kg (depending on model) :
- chassis 47 kg
- head 33 kg
• Disc cooling by water spray into the disc casing
• Minimum tank capacity : 40 liters.
• Water pump : 28 W - débit : 8 l/mn.
• Electricity supply :
- 230 V : H07-RNF 3 x 1,5
- 400 V : H07-RNF 4 ou 5 x 1,5
- 115 V : H07-RNF 3 x 2,5
MODEL POWER
LEVEL
LWA (DB)
EN ISO 3744
2,2kW - 230V 102 db
2,9kW - 400V 90 db
3 Inspection-Description of the machine
• On receiving the machine check its condition.
• Always keep it perfectly clean.
• Check the supply cable lead periodically.
• Always keep alert when working.
• Check the mounting of the components (abnormal
vibration).
SEE FIG. 1
Chassis-tank
1
Leg
2
Water pump
3
Retaining jack
4
Tightening handle
5
Transport wheels
6
Drain plug
7
Motor
8
Lack of voltage switch
9
Carrying handles
10
Disc casing
11
Housing cover
12
Movable table
13
Table stop
14
Movable table stop
15
Manufacturer's plate
16
Cutting guide
17
Table locking
18
Operating handle
19
4 Handling - transport
Dismantle your machine into two parts.
ABLE PART (SEE FIG 2)
T
• Remove the table by tilting it slightly so as to clear the
2 - Lg 3 m.
2 - Lg 3 m.
2 - Lg 3 m.
PRESSURE VIBRATION
LEVEL LEVEL
LPA (DB) G
EN ISO 4871 ENV 25349
91 0,21
81,67 0,029
14